Jump to content
SAU Community

Recommended Posts

Hey,

I'm looking at buying a Nissan gazelle and turning into a drift car, so i can learn to drift and gain more experience with modding cars before i am old enough to buy/drive a skyline.

I was wondering if there was any other sort of car that you would recommend for me to look at before i purchase a gazelle, that would make a good/cheap drift/project car.

Also, what engine would you recommend i put in it?

I chose the gazelle because i heard that ca18det/sr20det can just bolt straight in. (don’t really know much about engines tbh)

Heres one i am looking at there aren’t really many around :P

And about how much will it cost me to get it up and running as a drift car, not counting the exterior and interior work.

Keep in mind that i am:

17 years old

Wont be driving it around town, only on tracks

Have an income of about 160 a week

Going to put alot of time into it.

Also if you know anyone that is selling one tell me

Any help/advice would be greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/153849-gazelle-project-drift-car/
Share on other sites

you need to get one with indapendant rear suspension. part from thet they make great drift machines.

Also consider an R31 skyline, they do a really good job if they have a locked diff and hard suspension they put out about 100rwkw and its just enough to get them drifting.

Cheers.

Justjap have an immaculate factory turbo S12 in their lot right now that has to be seen to be believed. It has an original 120,000km on it or something but looks like its brand new.

Could i please have a link?

Also consider an R31 skyline, they do a really good job if they have a locked diff and hard suspension they put out about 100rwkw and its just enough to get them drifting.

That's with thier standard engine? and if i wanted to upgrade the engine in it how hard/expensive would that be?

R31/s with the standard RB30E put out very close to 100rwkw and hive quite a decent amount of torque.

their weight balance is not too bad and parts are cheap as chips :P

The best was to set one up purely for drift is strip everything out of the car just leaving 2 seats, dash and door trims and gut the rest this will help by keeping the car lighter.

then get the diff locked by welding it at about $50-100 and then buy really stiff springs far stiller than you would use on the road. around 5k rear and 7k front. they will set you back between $200 and $300

I have seen cars set up like this perform remarkably and having spent all of $1700 for the car and a set of springs and a welded diff.

you can also turbo the stock R31 engine using factory parts from a VL turbo but all up you will be looking at around $1200 for ECU, injectors, turbo, dump, crossover pipe, taking the total to $3000

and for a grand more than that you can buy an unregisterable race only import shitter like an S13.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...