Jump to content
SAU Community

Recommended Posts

pete cheapest is acl replacement bearings from your local repco etc.

Standar nissan bottom end bearings is $189+TAX, Holden I think was more again.

ACL standard replacement Ie. non race series. $96+TAX

Dave, Good work mate thats really nice for only 10psi, run her in quick so we can see what is really achievable!!!

GTST:

Wiseo forgies

eagle rods

2mm cometec (sp?) head gasket

stock rb25det head

greddy plenum

custom high mount with GT35r, .82 AR rear

I am told it has 9:1 compression

Notice on the graph how early it wants to shoot up in boost.. and in power!!

it is a world apart from the rb20, its just so nice to drive normally, Only booted it a few time but hell!!! its crazy

she's got a non name 45mm external that really screams on boost :P

I havent wired my tacho in yet, but yeah it wouldnt be the most accurate figure cuz its is running pretty fat at the moment, seems to choke on itself a little, then all of a sudden it just screams onto boost

My speedo isnt working yet either, its cable driven and the drives in the box, but nothing on the dash ?? :S, going to jack it up and pull out the speedo sender, bet it's snapped the cog off the drive :)

what happened to the R31 you had dave?

jeez seems like ages ago when we were talking about this stuff in the porto over a *number* of alcoholic beverages. good to see you got it going, only beat me by 6 months though :(

impressive power for that boost too, nice bolt-ons contribute i think :(

Thread too long to check, but I understand RB30 stock rods are tougher than RB25 rods?  By how much and why?  I hear they can handle ~400rwkW with all tuning working well.

Ho, ho, ho, standard rods :looney: :looney: :looney: 400rwkw ho, ho, ho

RB30 rods are longer

RB30's have a better rod/stroke ratio than RB25/26

This means they are subject to lower side stresses

Being 3 litres, it doesn't have to rev as hard to make the same power

So the RB30 will generate the same power with less rod loadings

But the RB30 rods in themselves are not as strong as RB25 or RB26 rods

Because they don't have to be

:P

Ho, ho, ho, standard rods  :looney:  :looney:  :looney: 400rwkw ho, ho, ho

RB30 rods are longer

RB30's have a better rod/stroke ratio than RB25/26

This means they are subject to lower side stresses

Being 3 litres, it doesn't have to rev as hard to make the same power

So the RB30 will generate the same power with less rod loadings

But the RB30 rods in themselves are not as strong as RB25 or RB26 rods

Because they don't have to be

:P

Yep, makes sense.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You know how your car rolled through a fence in your last jacking escapade? Scissor jacks increase the likely hood of that sort of thing happening immensely!
    • http://calfinn.com.au/product/1500kg-standard-trolley-jack-cj-2t-c/1500kg-standard-trolley-jack-cj-2t-c   I have this and fits under a S3 33 GTR with no issues. Purchased in 2009 and not one issue. It was $950 back then. Not cheap but something so important isn’t worth cheaping out on.
    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
×
×
  • Create New...