Jump to content
SAU Community

Recommended Posts

Finally fired the new machine into life with a slightly strange situation, Im running N1 pump, 26 head with 2 x 1mm restrictors. The strange part is I have fitted a mechanical autometer oil pressure gauge off the main gallery where the original RB30 oil pressure sender screw into & it gradually goes off the chart to 100psi at idle..... Im running 15/40 shell helix mineral oil, the std oil pressure gauge on the dash reads about 3/4. Not sure if I have an issue with the oil thickness or a bodgy gauge....

Anyone else had this?

I havnt fully warmed it up yet as still fitting the wideband sensor & want to make sure all is good

Cheers, Matt

I see 100psi at idle when cold (N1 pump), at normal operating temp. I see ~40psi at 2000rpm, ~60psi at 3000rpm, ~80psi at 4000rpm and 100psi after that. Hot idle sees 10-20psi depending on how hot the oil is.

I see 100psi at idle when cold (N1 pump), at normal operating temp. I see ~40psi at 2000rpm, ~60psi at 3000rpm, ~80psi at 4000rpm and 100psi after that. Hot idle sees 10-20psi depending on how hot the oil is.

Thanks, I warmed it right up last night & found pretty much the same result as yours, I was just a bit sus that I may have had something more sisnister causing it. Do you run a restrictor for your turbo oil feed? Im running GT3540 (brand new) & noticed a bit of oil in the compressor, I know they have small feed holes down in the cartridge but thinking I may need one in the block fitting similar to the standard banjo style or weather its just settling

come on strap that thing on i wanna see the response of it :P

lol

went to my mates workshop last night as he finally got the 26 back in the 32gtst that's in there. Took some measurements to see where the plenum sits in relation to strut tower etc. discovered I will need to get a 33 clutch master cylinder (which is good because mine just started leaking hehe).

Will be dropping the plenum off to be welded up later this week, once I get it back we can start bolting stuff on :O

Got a paintball tournament in 3 weeks and will be training a lot until then so it will be slow progress :O

Hi Guys,

just a quick question.

i have a R32 rb25de head with no cams and was thinking of getting the following:

2202-RN170, IN (256deg) (Lift 8.8) (valve timing 110)

2202-RN175, EX (264deg) (Lift 9.0) (valve timing 115)

what are your ideas on how these will go on a RB30/25 build

lol

went to my mates workshop last night as he finally got the 26 back in the 32gtst that's in there. Took some measurements to see where the plenum sits in relation to strut tower etc. discovered I will need to get a 33 clutch master cylinder (which is good because mine just started leaking hehe).

Will be dropping the plenum off to be welded up later this week, once I get it back we can start bolting stuff on :D

Got a paintball tournament in 3 weeks and will be training a lot until then so it will be slow progress :P

I'm having the exact same issue with an aftermarket plenum.

if you can post some pics with the r33 one installed that would be great.

What head are those cams to suit?

the cams are for an RB20DET

i was wanting to get 264 in and out but the person i have been talk to can only do the below combo.

the other option i was thinking was Tomei Poncams 256 in and out with 8.5mm lift

I'm having the exact same issue with an aftermarket plenum.

if you can post some pics with the r33 one installed that would be great.

Will do.

There is apparently some slight modification of the pushrod that needs to be made but my mate has done this before, I'll try document it for yas :D

If you have a look at your stocker one, imagine that the cylinder doesn't extend past the resevoir.. that's how big a 33 one is.

On another note, dropped my plenum bits off at the fabricator yesterday afternoon! :D

Will do.

There is apparently some slight modification of the pushrod that needs to be made but my mate has done this before, I'll try document it for yas :D

If you have a look at your stocker one, imagine that the cylinder doesn't extend past the resevoir.. that's how big a 33 one is.

On another note, dropped my plenum bits off at the fabricator yesterday afternoon! :(

I was also looking at aftermarket ones, i spoke to sydney race brakes who advised they should have something but for what price....

Another option is finding one from another make, alot of european cars have small cylinders with remote tanks.

Since my plenum is custom theres no rounded end so its the same heigh for the whole lenght.

Ill post pics when i get time.

I was also looking at aftermarket ones, i spoke to sydney race brakes who advised they should have something but for what price....

Another option is finding one from another make, alot of european cars have small cylinders with remote tanks.

Since my plenum is custom theres no rounded end so its the same heigh for the whole lenght.

Ill post pics when i get time.

$140 for a 33gtst clutch master cylinder. Shorten the pushrod slightly and bobs your aunty. I'm going to need to put mine in soon as I'm losing ~1/2 the resevoir in a little more than a day.

the cams are for an RB20DET

i was wanting to get 264 in and out but the person i have been talk to can only do the below combo.

the other option i was thinking was Tomei Poncams 256 in and out with 8.5mm lift

any opinions people?

  • 2 weeks later...

Im putting a 26/30 into my r32 gtst. I am going to buy a new standard balancer to go with it. Does anyone know which one is the best to use? I am thinking rb26 but are all the belts the same. I dont have A/C anymore so that ones not an issue

cheers guys!

from memory it depends which power steering pump you are using, and if the belts line up correctly. Assuming the alternator/water pump belts are the same.

but for the price of the ross units why not just get one of them?

Edited by TiTAN

I read a few pages back that there are engine mounts that can be used to lower the motor a bit. Can someone please:

1) verify that this works?

2) confirm how much lowering we're talking about?

3) confirm where to get these engine mounts from?

Oh yeah, we started up the RB2630 the other day after a long arse build - thanks to everyone here who gave valuable info through PMs etc. So far we've made 330rwkw on 14psi through the auto gearbox. Torque was at 487nm, and it was at this point where the flex plate in the auto gave up (see pic below)

flexplatedamage160908xx2.th.jpg

A new item has been sourced n sent down to MV Automatics for strengthening :bunny:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...