Jump to content
SAU Community

Recommended Posts

hey guys,

i have an r32 gts-t and my car seems 2 jerk in 2nd and 3rd when i floor it from 4000rpm onwards.

it feels like the car wants 2 go but sumthing is holding it back. Something must be causing it struggle.

This doesnt happen all the time but does happen

Any help would be appreciated thanx guysss

:ninja::):laugh:

Link to comment
https://www.sau.com.au/forums/topic/154372-car-jerks-at-times-plz-help/
Share on other sites

Too vague, we'd need more info than that, one thing I'm 90% sure of is that its' either fuel, electrical, or mechanically related though......lol.

lol... well when it happens the car doesnt flow smoothly sorta like somethings cutting out therefore it jerks so it could be electrical.

a mate of mine seems to think that it could have something to do with my engine coils, could that be right?

thanx

Nah, you can buy them in the FS section here. Then you just swap it for one on the motor, and keep swapping it until you find the faulty one.

Takes like 2 minutes to swap a coil once the valley cover is off.

At what revs does it jerk?

Nah, you can buy them in the FS section here. Then you just swap it for one on the motor, and keep swapping it until you find the faulty one.

Takes like 2 minutes to swap a coil once the valley cover is off.

At what revs does it jerk?

hmm sounds good might chek it out thanx

it starts to jerk between 3500 and 5000 after that its usualy finee

If it was a coil and above 3500rpm, I've reckon it would keep missing right through the rev range once it started. Secondary winding [if nissan coils have them, not sure] collapse would be at or over 3500.

Maybe the problem is elsewhere.

the car is pretty much standard apart from a cat back exhaust, pod a BOV.

standard computer

might change sparkies................

just out of curiosity how much would a bosch fuel pump be and will it change anything performance wise????

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...