Jump to content
SAU Community

Horn Playing Up

cheez

By cheez,
in General Maintenance

 Share

Recommended Posts

cheez Mentor

cheez

Posted
Posted

hey guys

my horn honks when i turn the wheel about a 1/2 turn either way but wont toot when centre and will go off again when a full turn is done.

atm the horn is disconnected so yeh, i need to get it working, any ideas???

Link to comment
https://www.sau.com.au/forums/topic/154443-horn-playing-up/
Share on other sites
Craved Grand Master

Craved

Posted
Posted

they work by earthing a circuit within the wheel, something on teh wheel is touching the wire to make it go off

what wheel is it, have you remove the horn centre if its aftermarket, and check that the wire isnt worn and is connected correctly

Link to comment
https://www.sau.com.au/forums/topic/154443-horn-playing-up/#findComment-2872416
Share on other sites
cheez Mentor

cheez

Posted
  • Author
Posted

i have the standard wheel, air bag in it, dont know how to take it off? the horn cover that is,

wasnt to embarrassing, when it happened just opened the bonnet and disconnected the siren part of the horn.

lol.

help

Link to comment
https://www.sau.com.au/forums/topic/154443-horn-playing-up/#findComment-2875407
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • iamhe77
      Might import a stagea

      By iamhe77 · Posted

      Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • iamhe77
      Stagea identification?

      By iamhe77 · Posted

      Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • GTSBoy
      My BMW E39 528i touring

      By GTSBoy · Posted

      Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...