Jump to content
SAU Community

Recommended Posts

BP is the only refinery in WA anyway, so technically it'll still be BP.

Usually other Brands put there own magic additives in the blend...

but otherwise it'll mean 98 will be easier to get in those situations where you would normally have to hunt for a BP... i think everyone here has had that experience at least once.

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2888871
Share on other sites

ok... who here every time they fill up on bp ultimate put a bottle of octane booster in as well? ive heard that the fuel in japan is 101 octane and that with our fuel we should put in a bottle of octane booster aswell

that would probably make your fuel 98.1 octane and give your plugs a beautiful orange colour

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2890148
Share on other sites

that would probably make your fuel 98.1 octane and give your plugs a beautiful orange colour

Dan, there actually some good octane boosters out there. Besides orange is pretty.

Can anyone CONFIRM where Peak get their 98 octane from. Is it in fact BP or is it from Singapore?

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2890485
Share on other sites

Well this is great news. The only reason I went to BP was because they were the only ones who had it, now that peak and caltex do i'll be able to shop around. Sure i'll probably only save a few cents each time I fill up, but it's more about the principal :laugh: (and the fact that I hate BP because they are always more expensive and bump up their prices randomly with no valid justification for doing so except to rip people off)

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2890902
Share on other sites

Well this is great news. The only reason I went to BP was because they were the only ones who had it, now that peak and caltex do i'll be able to shop around. Sure i'll probably only save a few cents each time I fill up, but it's more about the principal :laugh: (and the fact that I hate BP because they are always more expensive and bump up their prices randomly with no valid justification for doing so except to rip people off)

Well they all change their prices randomly. BP is no different.

Anyway why do you hate them so much. Just think where we would all be if BP didn't sell 98 Octane?

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2890932
Share on other sites

Just been on the phone to Peak. They often source their finsihed product from Singapore, but the chemist said their 98 is sourced from a Mobil refinery and is the same spec as the Utimate. I assume Caltex is sourced from one of their east coast refineries but I have not been able to confirm this.

Forgein ayyy! Good info skylion.

Should be cheaper but wont be as they colude to keep prices artificially high. Depending on what, if anything, is used to boost the octane rating, toluene (methylbenzene or phenylmethane) or ethanol it is reasonable to expect your tune up to change. I would be very careful with trying different fuel, check your AFR's and be prepared to make the changes. Hp gains have been made by Skyliners on the East Coast using Ethanol boosted fuels. Caveat emptor

Nicking fuel from the airport LOL mmmmm JetA1

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2891618
Share on other sites

imagine running jet avo fuel and having a bee*r limiter!!! = massive flames

pop, pop, pop, KERBANG, wooooooooooooooooooooosh!!!!!!!!!!!!

wouldn't adding ethanol and/or toulene be a good thing for your car as it burns better and cleaner?

if it is i can see how ur tune would change anyway

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2891921
Share on other sites

imagine running jet avo fuel and having a bee*r limiter!!! = massive flames

pop, pop, pop, KERBANG, wooooooooooooooooooooosh!!!!!!!!!!!!

wouldn't adding ethanol and/or toulene be a good thing for your car as it burns better and cleaner?

if it is i can see how ur tune would change anyway

keep it on topic please. there have been plenty if toulene threads before which has covered all of this.

Link to comment
https://www.sau.com.au/forums/topic/155318-98ron-at-peak/#findComment-2892058
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...