Jump to content
SAU Community

Recommended Posts

Hi. I noticed when I first got the car that it did not go into OD until it warmed up a bit and thought this was normal.In the last week or so I have noticed it is sometimes not going into OD. I would like to get some feed back to try and negate any costly trany work.Any one have the same thing?

cheers.

The S2 Triptronic has no OD button or power switch ( that I am aware off). It has only done this a couple of times. I just hope its a glitch and not an indication of anything bad to come.

OOPS! I'm only a simple S1, auto driver. See my 4WD thread.

it wont go into od (4th) until its warmed up. But should do so afterwards with no issue.

what he said. Its a feature, not a problem.

Some days mine takes longer to hit 4th gear than others, but I have a book from the car dealer I bought it from that says the transmission will not change into 4th gear (OD) until it is either warmed up or your speed requires it (i assume that means if you go over ~80km/h when its cold it should still change into 4th?).

If you find it has trouble going into 4th gear when it is definitely warm (ie. you've been driving for over 10 mins or so) then I'd be getting it checked out by an automatic transmission specialist. When was the last time you had your Automatic Trans serviced?

Yeah, it's another case of, the factory knows best. It wont go into 4th until the oil reaches a certain temp. Usually about 3k's down the road.

I do believe from experience that it is the tranny oil temp that we are talking about here, as the engine temp doesnt seem to have any bearing.

Thanks for all the info...I should have said this before.... but what I mean is the little change AFTER 4th gear! I assumed this was OD???...maybe its somthing else (lock up???)...or have I got one with five gears?haha..It definatly does have another shift after 4th on mine but only in normal auto..in sports or triptronic mode it stays in 4th...if you put it back to normal auto it does another shift. I guess another S2 triotronic owner could say if their car dose this.

putting it in sports/tipronic mode will raise the revs by around 500RPM and when you put it back into normal mode it'll drop those revs, if thats what you are thinking of as another shift, it's not.

Here is some info I got from an official Stagea site.

Transmission

Dualmatic M-ATx

(Electronically controlled 4-speed Automatic Transmission)

Gear ratio

1st 2.785

2nd 1.545

3rd 1.000

4th 0.694

Reverse 2.272

Final 4.083

so isnt final OD and what Im on about ?

Nup - final ratio is the diff, 'scott nuthin to do with the tranny, you are looking at ALL gear ratio's

Any ratio below 1.000 is overdrive, hence the name OVER drive as in diff being driven at OVER the engine speed

Edited by newbie101
...maybe its somthing else (lock up???)...or have I got one with five gears?haha..It definatly does have another shift after 4th on mine but only in normal auto..in sports or triptronic mode it stays in 4th...if you put it back to normal auto it does another shift. I guess another S2 triotronic owner could say if their car dose this.

Yep that's the lock up converter kicking in, the revs drop as it "locks up" the torque converter. This means there is no slip between the engine and the gearbox, as if you had a manual with a clutch engaged. And it is electronically controlled and must be excluded when the box is put into sports shift mode.

Cheers

Luke

Mine does exactly the same thing. I too thought that it was an overdive on 4th, sure feels like it. But as munch says it is probably the lock up convertor. Mine is only really noticable when I shift the stick into the tiptronic position, and 4 comes up on the dash instead of D. The revs definately drop. I haven't paid much attention to when it does it from cold. I will from now on. I'll let you know.

This is normal operation over 80km/h. I'm pretty sure mine's done it below 80km/h but as a general rule when over 80km/h at fairly constant throttle the torque converter will lock up. The revs may drop a little also.

If you put your foot down a bit (its usually fairly sensitive) it will unlock to allow you to accelerate again...much like dropping back a gear when you put your foot down a bit.

It will lock and unlock as needed, and it often only takes slight movements of your right foot to do this.

Hope that helps :wave:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...