Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Should have a petrol resistant foam rubber sleeve and hose clamp/s to mount it. I've not seen ANY shop including autosparkies that wire things up neat. Kindergarten kids could usually do better!!

They usually use the biggest soldering iron they can find, two rolls of dodgey insulation tape per job, have five twist joins in a 500mm length of wire, and crimp all connectors with a hammer or sidecutters.

LOL f*kn hacks!

What they figure is... if you don't see it.. it wont hurt you...

WRONG MUDAf*kRS!!!

They should take a crash course in how to unf**kthemselves.

OK OK, XXX did it. I spose its not bad to say it because i am sharing information that could be useful, as someone said if they cant see it it wont hurt them (the customer) or something along those lines. thats why i was so eager to get back in the tank and see what they really done.

First and last time to go there, wasnt happy with the service from the start.... i made an appointment at 10am and didnt leave until about 2.45.... but i spose workshops can be like that

i payed $120 for the install only... the pump was supplied by myself.

mods if u think this thread is not within guidelines than feel free to edit.

on a good note i got my FMIC installed today, happy with that and the guy who installed it

**edited by mods - please don't mention names**

I have a similar problem last workshop I left my car to gave me the car with

1 dint in the front passenger panel..denied by them.

1 window seal badly notched "drivers side"

1 side skirt chipped"drivers side"

I need to install cams/afms and retune.

I am not giving it back to these guys.

There work was good but are rough as guts on your car.

PM ME IF YOU WANT TO KNOW WHO THEY ARE IN MELBOURNE.

Probably best course of action if it hasnt been too long would be to sit down and consult with them, and maybe work out some appropriate resolution. but then again its upto how you would proceed in this circumstance. There are many and many dodgey work places, and very few that actually know what the hell they are doing with our cars and even less that will take the time, effort and care with out cars on anything mechanical. Hence why so many people do things themselves. Well one of the many things why anyway.

Noo good even still atleast you got to it sooner than later

it has been over a month since i done it, for the matter of 120 dollars i cant be bothered going back especially since they cant see it while it was installed. they will most porbably make excuses etc etc and highly doubt i will get my money back and i dont think there is anything else they can do for me.. i will just not go back there again

how much diff is the GTR pump over the stock? i would think the GTR would be easier to install than a walbro (aftermarket), I would think the GTR would use the stock mounting brackets etc. pm me the reply with the name of the workshop too. please thanks :)

walbro comes in a kit form and is so easy to install, it has a new hose with clamps, rubber mount down the bottom and pickup filter thing. also has a wiring harness with it. The hardest part is cutting the + and - and crimping/soldering them to the new harness LOL.

GTR pump uses everything the same so u dont need new hoses etc but it is slightly different on the bottom and wont sit in the cradle with the GTST rubber mount so this is where it gets ugly. If u a suitable piece of rubber and half a brain u could make a similar mount but yeah it help to have everything there when ur tank is opened up and u have no car to get bits and pieces lol

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...