Jump to content
SAU Community

Recommended Posts

Hi All

My name is Ron

Im new to this GTR thing and have a few questions to ask.

Firstly i have recently purchased a 93 R32 GTR and a PFC D-Jetro (thanks to Slide)

I was just wondering what would the costs be for -

1: to install and tune the PFC

2: to do a full service just to make sure everything is ok (as in change all fluids, belts, pumps?? )

and any other things that i should have looked at while its in the shop.

Any help is greatly appreciated

Thanks

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/
Share on other sites

Hey Ron!

and welcome to SAU and SAUWA :P

i can only help with my question;

1: to install and tune the PFC

-im not sure about the cost of installing the PFC. But tuning should be between $400-$600 for your 1st tune.

Best to give some of the workshops around perth and call and they will be able to quote you up.

Check out the The Consolidated Workshop thread

http://www.skylinesaustralia.com/forums/in...howtopic=141454

for a list of workshops NOR and SOR.

My personal recommendation for NOR is Hyperdrive (for tuning/services etc)

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2963186
Share on other sites

For a simple oil change in a workshop (eg XSpeed) you're looking at $180-$217 depending on the quality of oil used.

GT-R, go for the $217 one. They will also give you a report on what work may need to be done and the general overall condition of your car.

May sound like a lot, but it costs me $100 minimum to do my own oil changes, ~$90 for Mobil1 and $10 for a genuine Nissan Oil filter.

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2963228
Share on other sites

im due for my big service now, going to in tune performance, located in bibra lakes SOR, getting timing belt changed, all fan belts changed, coolant replaced, oil replaced, safc dyno tuned, walbro fuel pump fitted. costing $800.

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2963366
Share on other sites

im due for my big service now, going to in tune performance, located in bibra lakes SOR, getting timing belt changed, all fan belts changed, coolant replaced, oil replaced, safc dyno tuned, walbro fuel pump fitted. costing $800.

hey pal, where in bibra lake is that? i live there never seen it. Is the Walbro fuel pump included in that price or are they just puttin one you have in? i have also never seen your skyline around the area either :D

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2964454
Share on other sites

Thanks for all the info guys.

I live south of the river in beckenham.

I was thinking about goin to Top Racing but havn't heard much about them.

Xspeed seems to be the most recommend workshop so i might pay them a visit

to see what im up for.

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2965192
Share on other sites

Thanks for all the info guys.

I live south of the river in beckenham.

I was thinking about goin to Top Racing but havn't heard much about them.

Xspeed seems to be the most recommend workshop so i might pay them a visit

to see what im up for.

top racing provide good service and treat customers with respect unlike some other known shops.

plenty of people will recomend them on here

$217 oil change is a big big rip off, surely pulling a filter off and undoing a sump plug isnt worth $130, its about a 15-20 min job max. i suppose its good value if u got a 15L sump :P

Edited by CruiseLiner
Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2965726
Share on other sites

Top racing really know their work.

Every workshop has their pros and cons. But put it this way I'm yet to find a performance shop that stand behind their tune an ensure their work. The only other place I feel can do this would be Top racing after having dealt with 2 very well known performace shops when it comes to tuning the power FC D-Jettro, both their service and tune were very very poor indeed espically after "paying for what I got".

Rob

Edited by dan_the_man
Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2965816
Share on other sites

Thanks for all the info guys.

I live south of the river in beckenham.

I was thinking about goin to Top Racing but havn't heard much about them.

Xspeed seems to be the most recommend workshop so i might pay them a visit

to see what im up for.

give Top Racing a go

they arte the only workshop that touch my 93gtr

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2966315
Share on other sites

Hi all again

I think i will go to Top Racing. I gave them a call and were really helpfull.

Just have to wait till i get PFC and then im booking it in.

I will ask about a leakdown test to see what condition the engine is in to.

Once again thanks for all of the advice and recommendations.

Link to comment
https://www.sau.com.au/forums/topic/159601-service-costs/#findComment-2968648
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
    • Yeah the rule of thumb with an LS is 7psi per 1000rpm. That is decidedly not enough at 6800rpm. I mainly looked for the scenarios where knock started to be picked up and it was later in the session when things were hotter, and oil was thinner, and the pressure was lower than it should be. (i.e very horrible). I am hoping with thicker oil (I was running Penrite ten tenths 10-40, the manual specifies 10-30) that does not leak that it's much improved at that time!!! I am using Project Mu Club Racer CR pads. I'm also using the Project Mu 335C fluid. The symptoms imply that it was fluid that boiled, but no bubbles seemed pretty weird to me when I bled it today. I want to try Castrol SRF as it has a much higher wet temp but, well, I have new Project Mu fluid lol... so I should at least use that. The pedal on track was really noticable. It went from basically normal feeling to instantly near-floor. The car did pull up as before, it was just very much nearly at the floor before the brakes engaged. At that point I pretty much decided the day was very done, it did *kinda* come back during that very slow cooldown lap into the pits. Felt perfectly fine driving home.
    • f**king around with the bro
×
×
  • Create New...