Jump to content
SAU Community

Recommended Posts

HEY boys & girls

long story short.. i need a new engine... my car had an rb20det but yeah it died.. should i get another one.. for about $1000 or sh0uld i get an rb25det? they are newer, bigger & better lol ect.. how much more would i have to pay? $2500 for the rb25?.. has anyone got an rb25 for sale? :laugh: would it go in fine? no problems? :w00t:

and another thing.. i have about.. $3500 BUDGET :ninja: thats for the engine and install ..and prolly one of those major services ect. like timing belt and the oil and fluid top ups ect :rofl: lol i would shout u guys a carton and a good time if u wanted to meet up somwhere and do it all :laugh: i need to get in the circle of LOVE!

im lost without my r324door </3

haha does anyone have a flat bet tow trucK? ... just putting it out there :)

LUB JEZ <o/

Edited by 32JEZ
Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/
Share on other sites

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

following on from the PM's, I would recommend the Rb25 but not sure of whats needed in the gearbox department whether it bolts straight on or not.

3500 budget for a rb25?

nope... keep walking... you would ( while its open) replace any worn parts etc on the engine and possibly do the clutch at the same time ( since its all open)

for a rb25 ( + the ecu and wiring loom since the putahs are different) i would be looking at an upwards of 5000-15000

I got a few places to put a quote for me when i was thinking of putting an RB20//25 into my silvia and they broke down what needed to be done and what is reccomended..

they were not to far off each other and yah.. cheapest was 5000 and the most expensive was 15000 ( 15,000 was a complete rebuild + "bullet proofing" + after market gear)

So with your price range get an RB20 and do it right.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2977750
Share on other sites

3500 budget for a rb25?

nope... keep walking... you would ( while its open) replace any worn parts etc on the engine and possibly do the clutch at the same time ( since its all open)

for a rb25 ( + the ecu and wiring loom since the putahs are different) i would be looking at an upwards of 5000-15000

I got a few places to put a quote for me when i was thinking of putting an RB20//25 into my silvia and they broke down what needed to be done and what is reccomended..

they were not to far off each other and yah.. cheapest was 5000 and the most expensive was 15000 ( 15,000 was a complete rebuild + "bullet proofing" + after market gear)

So with your price range get an RB20 and do it right.

+ 1. normally all the wreckers sale for 5G.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978280
Share on other sites

I dont know much about the price ranges and acually bolting in the Rb25 but by the sounds of it, if you get a new RB20 and luckily you'll do it right and have some exra dosh over to get some nice upgrades.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978308
Share on other sites

stoking a 20 to a 24 is more effort than it's worth and it's not cheap anyway! With your budget, just stick to putting in a 20 again. You're going to have to pay someone to take it out, someone to put it all back in....and depending on where you go you'll use up your budget quicker than you probably think. Remeber he's not doing any of this himself....I assume? If you're LUCKY you'll have a bit of left over money for some bolt ons.

Link to comment
https://www.sau.com.au/forums/topic/160327-rb20-or-rb25/#findComment-2978673
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...