Jump to content
SAU Community

Recommended Posts

The reason why i ask is that i just bought mine and it has aftermarket ones installed. There is, however, a proper button which they are wired up to on the dash...

I have looked at photos of other 32gtrs and have not been able to identify where the standard ones are...

:P

In short, no.

But they are not so uncommon.

I didn't think they did, so do you know what the button is on the right hand side of the steering wheel above the rotating thingy which turns on the headlights and parkers?

They don't, but anyway.

The most common spot for the foglights in under the top section of the front bumper either side of the number plate. Usually the mesh screen for the interccoler/radiator cut out gets a couple of holes cut into it to fit the lights.

Do you know where they normally sit?

They sit right in front of your intercooler, on both sides, small ones.

There is a switch on the dash, its for fog lights and amber lights. Do a search on the forsale section, there had been a few pairs forsale lately.

Oh they might not be standard but definately a standard option.

I didn't think they did, so do you know what the button is on the right hand side of the steering wheel above the rotating thingy which turns on the headlights and parkers?

No, they're definately not standard, but may be an option (but I really don't think?)

The switch you're talking about allows the park lights to be on when depressed with the ignition key removed and the car locked (for when parked in a dark or dangerous position).

yes and no. the ones pictured are a dealer option available at time of purchase. they may have even been fitted at the factory, or if not fitted at the dealer when sold. but they are not standard.

  • 5 months later...

sorry guys.. i know this is an old post but i needed a bit of help. i was after some fog lights that would fit the spaces in my front bar pictured below. a pair would be nice but i dont mind just one and im after the really tacky looking yellow plastic covered ones.. any help would be great..

cheers, tushar

post-40010-1190510678_thumb.jpg

Why would you want to put fog lights in there? People usually leave it open for more air flow to the intercooler/radiator. If you want a fog light to be put in there, measure out how large the gap is and find a light to fit. I would assume it'll be hard finding some that fit perfectly though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...