Jump to content
SAU Community

Recommended Posts

oil in the catch can is usually from the crankcase ventilation or leaking from the intake

the usual culprit is the oil seal on the turbocharger, they can die / perish

a catch can simply catches it and does nothing more

its more like a fail safe / press F8 to go into safe mode kinda device

empty it out

check your intercooler piping for oil marks and clean them away

drive around for 2 days and check all again

if you have more oil back and piping is oily (as in substantional) then it could be shagged oil seal on the turbo

thanks paul...

yeah i know what the catch can does, i'm just basically asking whether it soulds like the problem is the engine or the turbo or something else?

so you think turbo on its way out?

i might go get a compression / leak down in the next few days while i keep my eye on the turbo and catch can..

As the other guys said.............. also.... could be happening is that u cracked a piston....... usually number 5 or 6. thus letting oil into your cylinder thus causing detonation thus no good!!! The car will run fine for a while but these are a couple of signs. Get it diagnosed properly. Ask your mechanic to do a 'leak down test' this should work out what and where its happening. I know all this coz i have the same problem!!!! except mine has not only cracked it has sh%t it self!!

Yes, you have a problem with pistons / rings sealing inside the bore. I once saw a R34 GTR that would effectively empty its sump into the catch can as soon as it hit boost - turned out to be a hole in a piston.

last comp test was done 1 month ago and was all fine. have spoken to the mechanic and he is going to do another one next weekend

he seems to think it might be PCV valve bolcked or stuffed, so i took it off properly and gave it a good clean

after a few days of good hard driving i haven;t seen another drop in the catch can yet..

I may be able to shed some light on it.

you were not suffering from blow by before the cams by the sounds of it. but since they were installed and even on the dyno you were getting blow by :(

I am guessing the cams have a much longer duration. if that is the case the overlap would be greater. and it has to go somewhere :D

I have seen it once before and the problem was cured with adjustable cam gears and 3 deg retard on the exhaust and a whole 5 degrees advance in the inlet.

There cars were regrinds and i do not remember the specs.

the car was making more power after the cam gear adjustment and no more blowby :D

Hope this helps!

did the cams produce more power?

cams produced about 7rwkw more at the top end but heaps more midrange... but that was with adjustable gears as well... not just cams on their own.. i have no idea what the gears are set at though..

when my mechanic checks the compression i will get him to look at the cam gears also to see where they're at..

yeah the poncams are 256deg duration and 8.5mm lift

yeah but if there's severe blow-by caused by a piston problem, then its going to show up on a compression test.. or so i have been told

the car is not blowing any smoke, and still drives exactly as it has the last 4 years i've had it. if there was no oil in the catch can that one time you would swear there's nothing wrong...

sowwie guys not offering any advice on this matter but just wanting to know how much leak down test cost and last.. my rear turbo exhaust previously ended up in the cat and i was told to get a test done to make sure it didnt damage anything else.. cheers

catch can has been installed as is for the last 12 months and nothing has changed, so unless one pipe has become blocked for some reason, its not the plumbing...

well will see how the drivability changes

obviously i'm trying to grasp hold of any hope here (thus why i'm trying to tell myself its something not serious) and denial is a powerful thing, but i'm just going to keep a close watch on it as its still driving fine

i appreciate everyone's input

Warren.

Leak down always shows stuffed ring lands, usual comp test doesn't always. Piece of mind to stop those sleepless nights get it done. As a bonus you know the condition of the motor a little better. Maybe take it some where else just for the leak down if your current mechanic believes a regular comp test is as good as a leak down at showing engine problems.

Good luck..

Give in to the dark side............<looks at avtar> You know you want to. :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...