Jump to content
SAU Community

Changing Spark Plugs!

dru32

By dru32,
in General Maintenance

 Share

Recommended Posts

nismoman18 Mentor

nismoman18

Posted
Posted

i know how to get the cover off and everything, then there are coil packs on top of each spark plug ? what do i do to get these off? I think you should replace them with like iridiums or NGK spark plugs, factory gap is 1.1mm but lots of line owners seem to regap to .8mm, at what rev range is it misfiring?

nismoman18 Mentor

nismoman18

Posted
Posted

u disconnect the battery and press the brake pedal for a few minutes to make it totally powerless, if uve got an alarm system u will have to turn it off or just let it go off from the back up battery like i did. If u really want to drain the power leave the car for a whole day disconnected (sourced from http://www.powerlink.co.nz/~graeme/faq/). Reconnect and then start, the ecu will do a diagnostics and advance timing till it has a knock then it will retard so its perfect. I did it on mine but i didnt do it properly cos my alarm was goin crazy so i just reconnected and wil do later

nismoman18 Mentor

nismoman18

Posted
Posted

im trying to work out how to get them out of the block, i pulled the plastic cap off and found that each plug has its own coil pack, isnt that cool, but how do i get them off without breaking sumthing. There are charts which u can prolly get from supercheap or sum mechanical place which shows damaged sparkplugs compared to a good one, and gapping them u should get a feeler gauge ($10) and just tap them gently till the gap is at .8 which is what ppl seem to like. the feeler gauge is to measure the gap, do not use a hammer or pliers, and iridium plugs shouldnt be regapped too apparently

DREMEN Rising Star

DREMEN

Posted
Posted

OK i did mine 2 weeks ago so I know the process......

-Once you have removed the NISSAN cover, undo the electrical plugs (one for each spark plug)

-Take off the plug (just pulls off)

-The you will be looking at the top of the spark plug.

-In your socket set you will have a really big socket (i forget the size) and use the extension arm, put this socket over the spark plug and undo.

- Be careful not to drop anything into the whole (do 1 plug at a time to avoid dropiing anything down there)

- Get the new spark plug, screw it in (VERY TIGHT)

- Put the plug back on

- Continue.

:D:D hope that helps :)

rwong20012 Apprentice

rwong20012

Posted
Posted

http://homepages.kcbbs.gen.nz/benk/gtst/Fi...ndplugmaint.htm

I did my spark plugs last week for my r33 gts25t

i just followed the instructions of the web page above.

BTW don't tighten the spark plugs too much and not to leave them too loose. read up about it on www.ngk.com.au they tell you everything about them.

But for the R33 spark plugs NGK (BKR6E11) just normal copper ones B = Thread length 14mm for this length the tightness of the spark plug recommended by Ngk was HAND tight then with the socket wrench another 180degrees of a circle..

Changing the spark plugs helped me solve the miss firing problem which occured for me at above 4000rpm but my spark plugs needed replacement coz they done like 15000km for copper that it

=)

being

blind_elk Grand Master

blind_elk

Posted
Posted
Originally posted by DREMEN

OK i did mine 2 weeks ago so I know the process......

-Once you have removed the NISSAN cover, undo the electrical plugs (one for each spark plug)

-Take off the plug (just pulls off)-The you will be looking at the top of the spark plug.

What about the 12mm headed bolts that hold the coilpack framework down on the sparkplug?
-In your socket set you will have a really big socket (i forget the size) and use the extension arm, put this socket over the spark plug and undo.
Use the right spark plug socket!
- Be careful not to drop anything into the whole (do 1 plug at a time to avoid dropiing anything down there)

- Get the new spark plug, screw it in (VERY TIGHT)

NOT very tight at all, NGK recommend about 25 ft/lb torque when the head is cold (and that's not a lot of torque)
- Put the plug back on

- Continue.

:D:D hope that helps :)

While you have it all apart, clean off the rubber boots on the coilpacks, make sure there's no carbon or moisture or stuff hanging around, as that can provide an easy path to earth for the spark pulse.
dru32 Collaborator

dru32

Posted
  • Author
Posted

hey i reset the ECU.. AND Oh yeh!!!, NOT ONE missfire!! I went to 7100rpms in first and second.. Sounds great without that annoying noise. Also it handles a bit different too.. Better actually.

If it starts to missfire again in sayyy a 2 months, is it safe to reset the ECU again?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...