Jump to content
SAU Community

Recommended Posts

do you have the dash surround where the head unit goes i just bought my r33 and the previous owner spray painted it and f**ked it up so if you have one how much i can pick up tomorrow call me on 0439802287

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

hey mate,

after these two parts:

passenger side vent face

http://members.iinet.com.au/~ahmedk/07-04-07_1513.jpg

drivers side door face

http://members.iinet.com.au/~ahmedk/07-04-07_1514.jpg

what's your price?

dude can you clean out your inbox so we can get pms through i would like to purchase the gtr wing off you im in melb and can pick up any time please pm me in regards to the wing or call me on 0433-672-888

I tried sending you a PM but your inbox was full.

Here's the PM:

Hey,

I’m after a few parts for my 1993 R33 GTS-T Nissan Skyline 2 Door, if you can help out that’d be great I read your post on the website so thought you may be able to help me out. The first two parts I need, the last two aren’t really of a concern mine just have a small crack about 1cm long – but I’d rather one that has no crack

If you could PM me back, that’d be great. Parts I am after are:

1. Intercooler and Piping (Aftermarket)

2. Turbo-back or Cat-back exhaust system. (Aftermarket)

3. Plastic surround that goes around steering wheel and CD Player. (Stock)

4. Left hand side plastic piece that runs underneath the door that says “Skyline” (Stock)

I’m also in Brisbane, and would rather pickup to make it easier, but if shipping is needed I will pay extra for that. Remember the car is a 1993 R33 GTS-T Nissan Skyline 2 Door.

Thank-you.

Please PM with your response.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...