Jump to content
SAU Community

Recommended Posts

easy way to pick them is look in the mouth of the front bar where the cooler sits.. the siren is there

the other way to pick out undercover cops is too look at the antenna, if its a tall one with a thick base (usually thick black rubber at the base) then watch yourself :D

Edited by Baconer
Link to comment
https://www.sau.com.au/forums/topic/161664-nice-cop-car/#findComment-3008888
Share on other sites

Signs its undercover cop car:

Plates are Normal issue - I.E Not a white,blue,purple, custom yellow, black etc.

Windows will have squares in them for lights ussually mounted top left and right corners and on dash front centre and rear centre top!

If stock car will have NO hub covers

Will have stock alloys if its a GT-P or any up-market performance car

Will floor it off the lights to waste petrol unless your infront.

Plates will now often have LPG sign as many cars are now going environmently friendly and also cheaper.

If non of these items are on the car (barring the lights) it is a impounded vehicle. Ussally only sporting some features if any, Almost always will have Blue/red lights in the blinkers.

Ussually two people will be in the car - two people are better than one at over powering a person if they get violent!

Although I've never been able to pick a cop car via its ariel they often do have a ariel front of the left hand side comming out of the bonnet gap, rear comming out of the boot gap (left hand side) or in stock position on the middle rear radio ariel situated directly centred on the rear window or above.

Hope this helps some people from being booked, if it doesnt then you deserve it.

Remember impounded and retrieved cars are virtually un detectable.

Oh and in NSW the undercover car of choice is ussually a silver GT-P ford because of its power, common-ness and hoon like apearence.

Edited by DECIM8
Link to comment
https://www.sau.com.au/forums/topic/161664-nice-cop-car/#findComment-3008931
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...