Jump to content
SAU Community

Recommended Posts

Hey guys,

This probably sounds stupid but how exactly tell the difference between a series one and series two R33 just by looking at it. And is there a difference in performance between the two?

Thanks,

Sammy.

Link to comment
https://www.sau.com.au/forums/topic/163075-how-to-tell-if-r33-is-s1-or-s2/
Share on other sites

Hey guys,

This probably sounds stupid but how exactly tell the difference between a series one and series two R33 just by looking at it. And is there a difference in performance between the two?

Thanks,

Sammy.

A series 2 from the front the Bonnet/ Grill is different, The headlights are a different shape and the front bar has those round fog lights and indicators in it. A series one has that funny grill with emblem on it and less angualr lights

From the rear the series one has that low rounded wing whereas the series 2 has a higher squared off wing

No difference in performance

PS prepare for heaps of people to tell you to search

There is little or no difference in performance between S1 and S2 (other than the wear and tear resulting from the fact that S1's have typically seen a few more years of service).

From memory, these are the main differences...

Interior:

Updated trim

Updated instrument panel

Passenger airbag

Exterior:

Round indicators and foglights

Sharper bonnet lines, grill and headlights

Chrome backing on headlights

Chrome 'S' Skyline symbol on bonnet

Color coded 'Skyline' trim under boot

Titanium coloured boot lock

Squarish rear spoiler

Mechanical:

Updated ECU

Nylon intake wheel on turbo

Updated ignition system

Different CAS for post Sept 97 models

There is a thread somewhere on the forum which has a detailed list of all the differences between S1 and S2 - do a search.

post up the interrior pic, pic of the gear shiift surroud and the dash surround

i think series 1 have the coin slot on the dash

series 2 have the coin slot on the gear shift surround

at least I think thats how it goes

you dont have a S2 unfortunatly, its a S1/.5

S2 are 96-98 models S1 are 93-95

Ummm no. u are wrong... very wrong, mine is a 95 series 2.. November build...

stick that up there.:)

OK so what series is this one...?

Yrs is a so called 1.5 dude

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...