Jump to content
SAU Community

Recommended Posts

ok, i have done a search but didnt come up with what i wanted

1 - my heater/aircon is stuck on demist, doesnt matter if i select head/feet etc, it stays on demist

2 - its stuck on heat, i can hold the cold button to override and it gets cold but... if i turn the unit off it starts venting hot air

3 - relating to above, i can select to recirculate the air but when the unit is tuned off it changes to the outside vent, hence it slightly blows hot air

:wave::(;)

Edited by Jbone
Link to comment
https://www.sau.com.au/forums/topic/163421-r32-demister-and-heat-stuck-on/
Share on other sites

It sounds like the climate control thinks its very cold and always blowing hot air? Could have a faulty temp sensor.

There is a temp sensor to the right of the ash tray. Its like three small slits. Thats a common sensor which detaches/faulty.

Also sounds like your mode door actuator may be stuffed. Hence not swapping from demister.

Run the diag as explained in the pic below to see if the temp shows odd numbers.

selfdiagqc8.jpg

Hope this all helps.

- Patrick

sounds like you have a mixture of the same problems as to what Rekin and i have. Run the diagnostics and let us know what you come up with. make sure when you run them, do it in full sunlight or you will get error 25. thats the sunload sensor located in the left hand corner of the dash board closest to the window. (looks like a small plastic circle)

i havent fixed mine yet as my car is getting a rebuild currently.

good luck and let us know what happens.

Cheers, Ron

  • 1 month later...
It seems that r32 ac units really have alot of issues. I have one that won't switch modes now and it won't heat or cool! :)

Have you seen the thread about R32 airconidioning in the DIY section? Has a lot of good info on the diagnositics. Do a test and see what you come up with.

  • 4 months later...
mines the opposite. it wont go hot stays cold. went to the pits to get my yellow off and they said my demister is blowing cold air even tho the temp is set to 30 degrees

Try holding down your 'heat' button for about 20secs (or until the sign 'FH' comes on). Your system should ignore all the sensors and push out the hottest air possible. If it's still cold, your motor which controls the hot/cold is stuffed or your heater core is stuffed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...