Jump to content
SAU Community

Where To Mount An Oil Cooler?

tjandriesen

By tjandriesen,
in Engines & Forced Induction

 Share

Recommended Posts

tjandriesen Proficient

tjandriesen

Posted
Posted

On the good advice of many of the track guys I purchased a Just Jap Racing 19 row external oil cooler for my R33 GTR. Now I needed to get it mounted. It makes sense that you mount it under the front bar / somewhere by the radiator so it gets airflow but precisely where? Does anyone have pics of how they have mounted theirs?

Link to comment
https://www.sau.com.au/forums/topic/164522-where-to-mount-an-oil-cooler/
Share on other sites
  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Omurru Veteran

Omurru

Posted
Posted

There's a thread in the diy section that shows one being mounted in behind the indicators on the front bar, I like this idea because it means your not adding extra heat to the airflow through the cooler and radiator. If there isn't enough room there though majority of people mount them between the cooler and the radiator, on the righthand side to keep the lines as short as possiable. Just make up some brackets that bolt to the structure somewhere

700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

I bought a Trust one for my GTR33...but the supplier supplied the r32GTR type which sat where my air-con goes.

Anyway...you will need to take off your bumper and wheel, including wheel arch and make up a set of custom brackets to get it to sit up-right.

Take the panel(Left Front) off a swell, this will help you alot..lol

Your hoses will not be long enough...so you will have to take measurements after you install the cooler.

If you have the relocation kit you will find you will also need a 90 degree bend from the oil cooler...or something of that angle to get a braided oil line to fit.

Good luck....I know I spent an extra $700 to fit the dam thing.....frustrating...

Ronin 09 Grand Master

Ronin 09

Posted
Posted
I bought a Trust one for my GTR33...but the supplier supplied the r32GTR type which sat where my air-con goes.

No you were provided the right one.

the R32 one from Trust sits in the front bar passenger side air intake.

the R33 one sits next to the driver's side headlight.

700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

Bob on gtr's there is hardly any room down on the drivers side.....Blow off valves are located there.

R32 GTR Type oil cooler sits in front of the radiator.

R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected.

Oh...don't mount it so rocks gravel or stones can damage it....you will be asking for trouble

As for the extra money that was spent on mine...it was for 2 braided lines..approx.....3 metres in lenght each..which ran across the front of the radiator....Custom brackets to set up the oil cooler..to sit upright. 2 angle bends for the relocation filter and another 2 for the cap which went on the old oil filter location.

So as I said......good luck...have fun

Beer Baron Grand Master

Beer Baron

Posted
Posted

tekin, not quite right mate. greddy make a number of different kits. for 32 GTR alone there is one that mounts in the duct on the passenger side (below the headlight) and one that mounts in front of the radiator and within those two types you can get different size cores. which ever type you order will come with the perfect length lines and brackets and even a little duct. greddy kit is by far and away the best one.

700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

TJ has not bought a greddy unit....but an off the shelf......19Row unit...which can only be installed below the passenger side front lights as I have discussed before.

So he is in need of the items I have listed above..........tj can you keep us informed on what you had to go through to install this unit...

seeing it was not specific to your car.

CameronBNR32 Proficient

CameronBNR32

Posted
Posted

Is there a rule of thumb to mount the oil cooler below the oil pump? I've noticed most oil coolers are mounted lower than the oil pump in the inner guards.

I have mounted mine in front of the radiator, and always wondered if its mounted too high? never had a oil temp problem on the track though...

post-19425-1176681336.jpg

skyrocker Rookie

skyrocker

Posted
Posted
Is there a rule of thumb to mount the oil cooler below the oil pump? I've noticed most oil coolers are mounted lower than the oil pump in the inner guards.

I have mounted mine in front of the radiator, and always wondered if its mounted too high? never had a oil temp problem on the track though...

post-19425-1176681336.jpg

242076901.jpg

I had the oilcooler mounted in front of the radiator, but this setup is much better. It's a HKS S-type, deflectors etc. are included.

Beer Baron Grand Master

Beer Baron

Posted
Posted

well it is better, but it shoudln't be a problem. my greddy kit has the cooler mounted down low, but the filter relocater is mounted up high. as long as the pump isn't too worn it will be fine. just keep an eye on pressure that will tell you if there is a problem or not.

Tekin, I was replying to this:

"R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected."

it is wrong. I have a 32 GTR. I have an oil cooler and it is not mounted in front of the radiator. yes you could mount it there but it's a crappy spot to put it as it gets little flow through the core. passenger side duct is the best spot on a 32 GTR and a 33 for that matter.

Ronin 09 Grand Master

Ronin 09

Posted
Posted

lol

anywho, whatever is the case, as baron stated one of the best places is in the lower bumper vent on the passenger side, either R33 or R32 gtr.

just remember to cut exhaust holes in the inner guard or bottom stone tray for the air that has passed through the core to escape.

otherwise the cooler will do..... Fark all.

CameronBNR32 Proficient

CameronBNR32

Posted
Posted
242076901.jpg

I had the oilcooler mounted in front of the radiator, but this setup is much better. It's a HKS S-type, deflectors etc. are included.

That looks really neat, I might relocate mine and make some deflectors, would work alot better...

Blitz Grand Master

Blitz

Posted
Posted
Bob on gtr's there is hardly any room down on the drivers side.....Blow off valves are located there.

R32 GTR Type oil cooler sits in front of the radiator.

R33 GTR Type oil coller sits behind the passenger side headlight.

So Ronin.....you have been corrected.

Oh...don't mount it so rocks gravel or stones can damage it....you will be asking for trouble

As for the extra money that was spent on mine...it was for 2 braided lines..approx.....3 metres in lenght each..which ran across the front of the radiator....Custom brackets to set up the oil cooler..to sit upright. 2 angle bends for the relocation filter and another 2 for the cap which went on the old oil filter location.

So as I said......good luck...have fun

Please mate, before you tell others they have 'been corrected', make sure you know what your talking about.

Trust makes various kits, including a 'radiator front' (radiator support mount) kit for BCNR33 and I should know, not because I read it on the internet, but because I have one on my R33 GTR.

Beer Baron Grand Master

Beer Baron

Posted
Posted

I know it's true also. not because I have one, but because I read it. but not on the internet. it was written on the toilet wall of Hobbys International in Shinjuku.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • GTSBoy
      R34 Handbrake light saying ON and intermittently flashing

      By GTSBoy · Posted

      Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • Duncan
      R34 Handbrake light saying ON and intermittently flashing

      By Duncan · Posted

      ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...