Jump to content
SAU Community

Recommended Posts

Gdays it looks like the common cold idle problem has hit my car(94 R33GTST). As i start her up in the morning the idle either rises to about 1500-2000rpm straight away or as soon as i start driving and stop at some lights. This occurs until operating temperature is reached where it goes back to normal.

Now i have done some research before i ask this question and am just a little confused on something. Is it this cold start valve causing my problems (which i assume controls idle when cold) or the AAC valve (which i thought controlled idle along with the ecu/IAC valve when normal operating conditions are reached).As you can see im a little confused. Due to being a busy uni student i dont have much time pulling of everything and giving it a clean so i only want to go after what i/people think is the main problem.

Any help would be appreciated

Thanks

Link to comment
https://www.sau.com.au/forums/topic/166150-common-skyline-problem/
Share on other sites

Sorry should of been a little clearer, i mean once i start it, it will sometimes idle at its normal cold start value what your talking about but then i take it out of the driveway and drive it around for a little bit and then i stop at some lights and poah it shoots up to about 2000rpm while im sitting there and doesnt go down. Its like a valve forgets to close/open or something thats my problem and why im asking.

Thanks for the quick replies so far guys

Sounds like your automatic choke dude, although 2K RPM is higher than I'd expect it to sit on

agreed... a bit high... but none the less, it has been really cold lately... it doesnt use much petrol, and its mostly good for the car...

as long as it doesnt do it after like a 30 minute drive then your fine...

Thanks for the reply guys, well i could leave it for 5 minutes to warm up and then start driving then when i stop instead of idling at normal rpm's it will idle somewhere close to 2000rpm. I know its not a normal thing because i have had the car for like 3 years without this happening before. And it has also occured after like 20 minutes of driving just last night. So im very confused. I know about cleaning the AAC valve and that but is there a separate valve what controls the car at idle when cold or is it just the AAC controlling idle? If people could clear that up for me that would be great thanks. :ninja:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...