Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

*slap @ Dave

still waiting on response from Anna, if any :P

response is coming... just waiting for dad to pull his finger out and get me the prices :( I have been harassing him every day... usually takes a week with this method to get what I asked :(

oh. and by the way. unless its ripped from a 205 litre drum its not cheap.

at autoban and any other retailer the markup on oil is around 15-20% and trade is the same price. its always on specal and there is no money in selling oil retail.

castrol is the worst. every catologe sale its below cost. so putting it simply unless its in baulk its not cheap. and if it is someones getting ripped off :laugh:

group buy on 20L drums?

would going to a motul wholesaler as a club do anything for us?

Not sure... il get the name of where TAFE (well the teachers ordering it ...lol) and we can take it from there...

On a brighter note, dad assures me he will get the info this afternoon or tomorrow morning. Il post it up on Monday as I am generally never on SAU over the weekends.

So you use the 10w40 Richard? Cardigan boy has convinced me to go to 10w50.

yeah I use the 10W40. I think the 10W50 is a bit overkill. I never really get oil temp above 115C on the track and the oil pressure is always good. the chrono has very high film strength etc so I just never thought about going to a 50. plus the closer the first number is to the second number the better as there are less friction modifiers needed then. so a 40 is 4 times the 10, a 50 is 5 times the 10. i don't think there'd be much in it though.

yeah I use the 10W40. I think the 10W50 is a bit overkill. I never really get oil temp above 115C on the track and the oil pressure is always good. the chrono has very high film strength etc so I just never thought about going to a 50. plus the closer the first number is to the second number the better as there are less friction modifiers needed then. so a 40 is 4 times the 10, a 50 is 5 times the 10. i don't think there'd be much in it though.

Cannot find 10W50 on the Motul site, they only have 15W50. So with your theory, 15 into 50 is 3.3333.... Which is the better oil?

Cannot find 10W50 on the Motul site, they only have 15W50. So with your theory, 15 into 50 is 3.3333.... Which is the better oil?

well in that 50 is only 3.3 times 15 and 40 is 4 times 10 the 15W50 is 'better', in that it will most likely have less friction modifiers used in it. BUT it's only one aspect of the oil question. best thing is to pick an oil which best suits your car, and usage. :rofl:

group buy on 20L drums?

would going to a motul wholesaler as a club do anything for us?

This is a great idea!^^

http://www.linkint.com.au >> Australia Distributors for Motul

I'm also in for a 20L drum of Chrono 300V if its possible.

I think a group buy on oil would go ballistic - it's not like its a part that people would choose to buy or not, everyone uses oil whether they like it or not! >_<

Sorry I meant 15w50. It's the 300v Competition. I have been thinking about using the Chrono for winter but my car has always run fairly hot so I appreciate the extra thickness at high temp. I probably should use a better quality oil cooler but the one I have works ok and the 15w50 gives me the protection I need.

I do notice quite high oil pressure when cold and am particularly careful when warming up the car because when using a thicker oil like this I think the turbo is more suseptible to damage due to lack of oil flow. I never boost at all before the water is up to temp and would be lucky to hit 0.3bar before the oil temp has risen.

As BB says, horses for courses. I am more regularly at 120-130 degrees towards the end of a session whereas he is more around the 105-115 I'm guessing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
×
×
  • Create New...