Jump to content
SAU Community

High flowing the stock turbo


Recommended Posts

Guest MFX_R33
How much extra power would u get from High flowing it... Just curious.. Will it reduce the reliabilty of the turbo.

I have got 205kw @wheels with this turbo at 17psi (this is pushing the efficiency limit of this turbo). The standard turbo has ceramic wheels, which have a tendency to de-laminate at around 14psi causing the turbine wheel to end up in your exhaust.

As far as it spooling up slower, I havn't noticed any difference. It spools very easily with almost no lag (as with the standard).

Jeff.

Originally posted by MYGTST

the standard unit is made by hitachi

garett quoted me minimum of $1000

benifits are you can run more than 14psi reliably

downside may take longer to spool up and it will no longer be ball bearing

and no they can`t convert it to BB iv been told

I'm not sure but do series 1 have BB?

Originally posted by MFX_R33

 

I have got 205kw @wheels with this turbo at 17psi (this is pushing the efficiency limit of this turbo). The standard turbo has ceramic wheels, which have a tendency to de-laminate at around 14psi causing the turbine wheel to end up in your exhaust.

As far as it spooling up slower, I havn't noticed any difference. It spools very easily with almost no lag (as with the standard).

Jeff.

Did you just get the compressor side hiflowed? It musnt be if u r spooling at 2500

I got both sides hiflowed ($1000) and im hoping for 200kw@12psi.

Starts spooling at 3000 full boost 3500

we'll see next week when i get her tuned on the dyno with the SAFC

Guest MFX_R33

My Hilux looks the goods, and has a nice tan leather interior, but it is no SR5 :D. Mine is a Grinner, ex-Repco delivery ute. Full time LPG, 1.8l, 4 spd. It's a slug but it looks ok for a work ute (pics on my site www.mfx.com.au under Team). Anyway I have a Skyline to go quick :D.

Jeff.

Jeff just looked at the pics of you lux and line the line looks mad!!

I really like the look. so different!

and your lux is great for a budget build as well.

how do you find the EMS is it as responsive as the the factory ecu how is it at low speed and rev's .

cheers

meggala

Guest MFX_R33

Thanks all :cool:

Meg. The EMS is good if it is tuned properly. I can't say that it is as good as factory. For top end it is great, you just need someone to spend the time to tune it properly for cold start idle etc. At the moment I still need to get the cold start tweaked, but aside from that it is cool. Other benefits of the EMS over PFC is the fact that you don't need the car to keep all factory or close to factory sensors, like AFM's (I still have mine on there but it isn't doing anything), plenum idle sensors, etc. I looked at a PFC but with the custom plenum and XF throttle body it was too much stuffing around. Also the amount of other options with the EMS is mind blowing.

Macka. I got the Trust bonnet from Bodyform motorsports in Sydney but it was for a GTR and I had to do ALOT of modifying to make it fit. The GTR bonnet, believe it or not, is 20mm longer than the GTSt's. The mounting brackets had to be moved as well as heavily modifying the bracing underneath so the thing would close! It still is no quite right yet as it sits flush top and bottom with the gaurds but it sits high in the middle.

Jeff.

MFX - just saw your hilux - nice interior.

Where did u get it retrimmed?? and how much would it actually have cost if you had to pay. My hilux has recaro interior and im thinking of retrimming them in leather and suede. Got any numbers I can call to find out costs?

thanks

Dave.

p.s - what did you use on the dash? has it been painted, or covered in leather.. or something else?

thanks. mfx's dash looks so nice. I gotta find out how he got it looking so clean...

currently my 4wd has:

single battery

k&n cold air intake where 2nd battery used to be

turbo smart boost controller (12psi)

autometer boost gauge

tinted (got that done yesterday)

and over the next month i am installing a stock r33 intercooler as a topmount where the old airbox used to be..

i am hoping for around 60+ kw at the wheels :cool:! but hey, they are 45kw standard so a 20kw increase would be good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...