Jump to content
SAU Community

Recommended Posts

Looking at fitting either of these turbos to my RB20. Any feedback from people who have experienced this engine/turbo combination 1sthand? I have been told I need a spacer plate for the Trust turbo but does anyone know if it will fit up to a split dump pipe? Any help would be greatly appreciated

Link to comment
https://www.sau.com.au/forums/topic/171078-trust-td0506-vs-gcg-hi-flow-on-rb20/
Share on other sites

Ive got a GCG hiflow on my RB20. although it's not tuned yet so im only running 10psi.

but even then it goes alot better then the standard turbo ever did on 12psi and pulls all the way to redline.

Less response of course but not as laggy as you would expect.

Here's a link that gives some idea of the different impeller sizes on the MHI/Trust turbos vs Garrett.

http://www.900aero.com/main/tech_main_turbo.htm

I think a lot of the MHI gear is fairly heavily turbine biased, so Trust use a bit of mix-n-match to chase quick response. Pity that they use the 3 bolt turbine inlet, because genuine MHI turbine housings in TD05 and TD06 are evidently a T3 flange.

The Td05/06 turbo is a excellent match for the RB20 imo. It does require a spacer plate about 10mm just so the comp cover clears the manifold. With supporting mods you will get around 240rwkw. Cant remember about the dump pipe but any decent exhaust shop would be able to make split entry dump for it. Havent had any experience with the gcg hi-flow though so dont know which is better. BTW it is a T3 flange.

I had a tdo6 20g on my rb20 (240kw@wheel) and hated it. Lag, then wheelspin snap. Nothing at all in first gear unless u wanted to thrash the poor girl to about 7500-8. Same turbo now on the 3 litre motor and much much better. Total power not much more (280) but good grunt at 3 instead of 4500 - 5.

I 'think' it's a 10cm, but not totally sure. It was very very snappy on the rb20 tho, real hard to control power in lower gears. Straight line not too bad but try driving fast on a windy road - just forget it - I'd get beaten by a 180kw car easy. What a difference a litre makes eh.

I 'think' it's a 10cm, but not totally sure. It was very very snappy on the rb20 tho, real hard to control power in lower gears. Straight line not too bad but try driving fast on a windy road - just forget it - I'd get beaten by a 180kw car easy. What a difference a litre makes eh.

Post in the rb30 dyno results sticky thread in FI. :whistling:

Looking at fitting either of these turbos to my RB20. Any feedback from people who have experienced this engine/turbo combination 1sthand? I have been told I need a spacer plate for the Trust turbo but does anyone know if it will fit up to a split dump pipe? Any help would be greatly appreciated

the t05 turbos are a direct bolt on for Rb20, they also come with a dump pipe that joins to any aftermarket front pipe.

the 16g is good for 200-220 at 1-1.2bar

the 18g is good for 220-250 at 1-1.2bar

have used both extensively, and are a great bolt on solution. the 16g is super responsive but runs out of puff up top if you want to make much more than 220rwkw without cams etc.. I find this turbo far to responsive and prefer to use the 18g.

Edited by URAS

^ mate i waited 3months for slide to high-flow my turbo. in the end i got my turbo back and went to GCG, same week got turbo and never looked back. do a search on slide turbo u will see alot of people are pissed off waiting.

^ mate i waited 3months for slide to high-flow my turbo. in the end i got my turbo back and went to GCG, same week got turbo and never looked back. do a search on slide turbo u will see alot of people are pissed off waiting.

What supporting mods are you running with your highflow? Aiming for 200rwkw's, I am hoping to get away with highflow, fuel pump, exhaust, cooler & remap. Want to leave injectors, FPR, AFM etc. stock at the moment due to money, or lack of. Do you think this would be achievable? Also what is lag like compared to stock?

^ mate i waited 3months for slide to high-flow my turbo. in the end i got my turbo back and went to GCG, same week got turbo and never looked back. do a search on slide turbo u will see alot of people are pissed off waiting.

hhmmm??? 'sif anyone would ever get pee'd f at Aaron, as nice a bloke as you'll ever meet.

I waited 12weeks for one last year (between Aug-Nov) and couldnt have been happier.

Slides overall health is of most importance; yes he does have a health issue and yes he does get very busy with the huge quantities of orders he receives for his hiflows. For the cost/quality of the unit I think its an awesome deal never mind if its a 3month turnaround.

If youd bothered to read his area of the forums, instead of stirring up crud:

"Hi Guys

Orders are now being taken for highflows again

We will not be doing the sort of numbers as we used to so when orders peek at 20 we will stop until all are done.

This is simply to reduce waiting times due to the amount of orders we receive.

The waiting times will always be stated at or longer then 3 weeks regardless of if it will be done in 2 days.

This will be to avoid any possible delays that may push back production including my personal health."

Slide highflow FTW !!11!!!!!

^ any experience with a td06 19c?

nah as it isnt part of the performance range, i think it was more a mitsubishi factory repalcement part, rated @330hp. Ralliart starions and pajeros.

Edited by URAS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...