Jump to content
SAU Community

Nissan Genuine Part Numbers


arbess

Recommended Posts

  • 1 month later...

In desperate need or left hand rear wheel bearing for the following:

VIN: WGNC34 127902

Model: TGKPREFC34UDA--A--

Prod: 9903

It's a 99 Stagea RS Four S (Factory Manual)

43281-40P05 LH

43280-40P05 RH

Link to comment
Share on other sites

  • 1 month later...

Look for r33 door handle surround. Piece behind the door Handle interior mine broke when I took them off thank you!

If you mean what I think you mean then these should be right. Not sure about interior colour though. They are the same for front and rear doors for a sedan as well.

ESCUTCHEON-INSIDE HANDLE LH - 80683-70T02

ESCUTCHEON-INSIDE HANDLE RH - 80682-70T02

Link to comment
Share on other sites

  • 4 weeks later...

hello

chasing the part number of the main supply hose from the reservior to the power steering pump for a 98 ER34

pic of it attached - light is shining on it.

cheers

post-59710-0-74860200-1327382393_thumb.jpg

Edited by C BOMB
Link to comment
Share on other sites

er34-031157

GGKBRTFR34UDA-JJ-F

5/2000

Needing part number for

coolant overflow bottle cap

and on the oil cap.. if the seal comes seperate or part number for the whole cap!

Muchly appreciated!!

Link to comment
Share on other sites

er34-031157

GGKBRTFR34UDA-JJ-F

5/2000

Needing part number for

coolant overflow bottle cap

and on the oil cap.. if the seal comes seperate or part number for the whole cap!

Muchly appreciated!!

Coolant overflow bottle cap 21712-50M01-

Oil cap 15255-1P103-

13276-4P100-

XVqMr8.png

Link to comment
Share on other sites

  • 2 weeks later...

hi

i was wondering if you can give me the part number for the oil filter housing on a rb20det for an r32

also for a remote control key for an r34 gt-t

thanks

steve

Oil filter bracket

15238-80S00-

Gasket

15239-71L00-

Remote control key

H0564-C9920- ??????

LO1pB0.png

eKr99S.png

Link to comment
Share on other sites

  • 3 weeks later...
  • 3 weeks later...

Anyone know the part number for 34 v spec 2 front seats? (eg, the black ones)

I've put a few v spec 2 VIN's into FAST but they just give an error message

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You won't make it out of your driveway. Both your rear wheels will go in whichever direction they feel. Your Hicas rack or a lockout bar is required to keep your wheels straight. 
    • Updating results.  Using ATR45SS-0 model VS UHF57-900. Those two are very different turbos, different wheels sets with different wheel hub profiles but yet with almost identical result. I’m intrigued with both turbos performance. ATR45SS-0 was a 61mm turbo first developed in May 2020, UHF57-900 was a 62mm turbo developed in March 2024 as a powered up alternative of a G30-900. On paper ATR45SS-0 maxed at 563rwkws, while UHF57-900 maxed at 568rwkws. ATR45SS was slightly more responsive with slightly better power band through the mid range.  Road driving ability, ATR45SS-0 had better throttle response, felt more robust under throttle, as it wakes up earlier. I think G series wheel hub design made it to have higher inertia under light throttle. Doing bit more prototype work in the next few weeks, will update result when its back on dyno again. ATR45SS0 Blue, UHF57-900 Red Chequered tuner's Dynapack hub dyno, E85 fuel. Mod list is in video below video_20240604_114214.mp4    
    • Did you run the power cables for the mac valve to the other side of the car near the fusebox? Utilizing the stock boost controller cables? or did you run new ones?
    • Hey I have a potentially stupid HICAS question 🤣 I'm currently doing a full hicas delete, Power steering pump modified to non hicas, all lines removed from the car along with all electronics. My stupid question is - Do I need a lock out bar? is there any reason why I cant just remove everything from the rear end? I already have a lock out bar but thinking to save a few extra grams I could also get rid of the arms and tie rods as well and just run it with nothing in its place? or would it have a negative effect on handling?
    • Hi how are you guys?  I know i have been absent for years but im coming back slowly guys just wondering if anyone know where the ball joint on the NISMO arm front and rear can be replaced with OE parts?  Also  i know this is not the thread looking for springs and blistein shocks for the 260rs. Please advcie     cheers    yudy
×
×
  • Create New...