Jump to content
SAU Community

Recommended Posts

things to consider.

there should be no wire on the loom for pin 51 if there is no traction control on your car. having spoken to EGA4IT and he says he has seen one car (maybe a later model with a wire in the loom). he said the zener diode is not in backward on the diagram they are reverse polarity (i hope i am translating accurately).

regardless of whether you have a wire or not, you are trying to fool the ECU into thinking there is 3.7V so it 'thinks' traction control is working.

if this modification is made you need to test that the voltage TO pin 51 is about 3.7V or else you have made a mistake.

if the checklight is still on make sure that the boost controller is turned off on the powerfc as this is the usual reason the checklight stays on when first installed.

Edited by wolverine

Thanks for that, Ill give that a go...

I just tried to turn the boost control off but of course it is in Japanese so i am assuming it is off at the moment as it has a diferent japanese character to the other warnings which i am assuming the tuner left on..

Thanks again to all for your help

Dave

things to consider.

there should be no wire on the loom for pin 51 if there is no traction control on your car. having spoken to EGA4IT and he says he has seen one car (maybe a later model with a wire in the loom). he said the zener diode is not in backward on the diagram they are reverse polarity (i hope i am translating accurately).

regardless of whether you have a wire or not, you are trying to fool the ECU into thinking there is 3.7V so it 'thinks' traction control is working.

if this modification is made you need to test that the voltage TO pin 51 is about 3.7V or else you have made a mistake.

if the checklight is still on make sure that the boost controller is turned off on the powerfc as this is the usual reason the checklight stays on when first installed.

thanks mate, that explains everything

nice and easy, cheers again

thats what my mechanic said that you cant get the exact ohm stated resistors

it doesnt have to be exactly 400 ohm, it could be 500 or even 300 ohms, the idea is to provide a reasonably high resistive path back to negative so that current does not flow through the ecu in the event of some sort of failure/short.

also the zener diode needs to be installed in reverse bias. your auto electrician should know what this means.

it doesnt have to be exactly 400 ohm, it could be 500 or even 300 ohms, the idea is to provide a reasonably high resistive path back to negative so that current does not flow through the ecu in the event of some sort of failure/short.

also the zener diode needs to be installed in reverse bias. your auto electrician should know what this means.

thanks andy

awesome news

cant wait to hook mine up and 'see' what happens :D

  • 8 months later...
  • 8 months later...

i have had a few pm's and just thought id add a quick note to prevent confusion/frustration, if u cant find a 10.3V zener diode you can use multiple diodes that add up to 10.3V as long as they are connected in series

  • 1 month later...

Hey Guys,

Having some trouble with my powerFC. My car to clarify is a ER34 (R34GTT) that has had a conversion to manual. the powerFC throws up a backlight on the THR sensor with a voltage of 0.00. The car runs perfectly after an init clear. however I have some problems. MIL light is always on, TCS light is on and cannot be toggled with the TCS switch on the dash. the Aircon turns on but the compressor does not and last but not least HICAS light is also on.

any ideas if my series 1 R34 has the same problem as the Stags?

Cheers.

  • 3 months later...
  • 2 months later...
  • 5 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...