Jump to content
SAU Community

Recommended Posts

Near new Tein Flex, travelled around 5,000kms. Will pass any inspection. Come with EDFC Controller and solenoids (worth over $450) , 8kg/cm (Front) & 6kg/cm (Rear)

Circumstances have changed and i have sourced higher spec shocks with alloy bodies which i hope will better suit the track work my car does.

Asking $1600 for shocks, EDFC and even stickers :worship:. Located in melbourne, rather not post, but willing to courier at buyers expense.

SOLD

post-462-1183714558_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/175581-r32-gtst-tein-flex-with-edfc-sold/
Share on other sites

Cant honestly answer as they are in my living room. If someone buys my Bilsteins i have for sale then these will be going in for a month or so until my new springs/shocks etc are sorted. If someones buys these then Bilsteins will stay in the car until the new gear is arrived.

If your looking for day to day comfort and still great handling the Bilsteins are far better for the street. My theory is with normal road tyres you never have enough grip to need this high a spring rate on the street. But my car is mostly used for drving to/from the track, with the occassional long run interstate so...ride comfort was not such a concern when i grabbed the Teins

I purchased these as on the track the higher spring rates (which are the std springs for the teinss...so i hope well matched) will mean that with semi slicks on and far higher grip levels and corner speed, the car would be a little more balanced with less pitch under brakes. For a street car i cant see them being bear as good as the Bilsteins. On the track the Bilsteins would be equally as good, until you put real grippy semi slicks on the car then the Bilsteins fall over a little without re-valving for higher spring rates (well thats my 2c anyway :worship: )

Have got another set of Teins, though they are the RA. I understand that they are the top of the range Tein, only ones better are the ones with the remote reservoir. They are alloy, and the Melb workshop who i want to use has done some great things with them on other peoples cars....so will see.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...