Jump to content
SAU Community

Recommended Posts

Anybody know how to hook up a dual AFM setup on a RB25DET ? Right now Im running a single Q45 3,5" AFM but I'm going to max it out with the new turbo so I was thinking about making a Y-pipe for the intake and use dual Q45 AFM's.

Im running powerFC, can I just paralell couple the AFM signal wire or will this not work? The GTR with dual afm...does it have 2 signal wires on the ecu?

Link to comment
https://www.sau.com.au/forums/topic/177223-dual-afm-on-singelturbo-rb25det/
Share on other sites

you will need to either change to GTR PFC or you can use apexi SAFC II to parrallel up the AFM signals

i believe the unit lets you choose which mode to interpolate the afm signal, avg, max, double, half etc

just dont do any correction on the maps and use it as an AFM adapter/splitter

Anybody know how to hook up a dual AFM setup on a RB25DET ? Right now Im running a single Q45 3,5" AFM but I'm going to max it out with the new turbo so I was thinking about making a Y-pipe for the intake and use dual Q45 AFM's.

Im running powerFC, can I just paralell couple the AFM signal wire or will this not work?

Why have 2 AFM's? You don't need them, you can tune off one. So just use a "Y" inlet, the Q45 AFM on one and no AFM on the other.

The GTR with dual afm...does it have 2 signal wires on the ecu?

Yes

:D cheers :D

  • 1 month later...
What setup are we talking about?

Bottom end:

RB25DET bored 2580CC

Wiseco forged oversize pistons

Eagle forged conrods

Calico Racing bearings

Top decked

Head:

Shaved head

Ported and polished

Valve and valveseat cut

Tomei poncams 254

Cometic multilayer steel gasket 1.6mm

Other:

OBX T4 Pulse split manifold

OBX 50mm wastegate

Garrett GT4088R pulse split turbo

JUN-style intake plenum (portmatched)

Q45 90mm throttle body

Q45 90mm MAF sensor

Nismo\JECS 800cc injectors

Nismo Adjustable fuel pressure regulator

Apexi PowerFC

Apexi pod filter

Apexi AVC-R boostcontroller

HKS SSQV bov

Innovate Motorsports LC-1 with XD-16 Wide Band Kit

BOSCH 040 fuel pump

Oil catch tank

Oil cooler and filter relocation

OS Giken twinplate racing clutch

HICAS removal bar

Hybrid FMIC

3" straight exaust with 5" jap exaust tip

Why have 2 AFM's? You don't need them, you can tune off one. So just use a "Y" inlet, the Q45 AFM on one and no AFM on the other.

Yes

:( cheers :spank:

Because I maxed out the q45 afm I have already at 1.0bar, and I'm currently running 1.5 bars. And I want to go even higher =)

Because I maxed out the q45 afm I have already at 1.0bar, and I'm currently running 1.5 bars. And I want to go even higher =)

pretty sure SK is saying u dont need two afms. and that if u set it up the way he said, then a whole lot of air would by pass the afm, im guessing lowering the volts its reading and allowing u some tuning room again.

i could be wrong tho :(

upgrade to map sensor?

I agree with that also.

Go to a MAP. I think most standard internal MAP sensors are roughly 25psi (Wolf/Microtech), then you can upgrade to an external MAP which goes to about 35psi roughly.

Abu

Edited by abu
Because I maxed out the q45 afm I have already at 1.0bar, and I'm currently running 1.5 bars. And I want to go even higher =)

Do you get what he meant though?

Doesnt sound like it as it would solve your problem, and not cost much

Because I maxed out the q45 afm I have already at 1.0bar, and I'm currently running 1.5 bars. And I want to go even higher =)

Not that I think much of Autospeed these days, but this might explain what SK means about using just one AFM...

http://autospeed.com.au/cms/A_2424/article.html

Changing to map sensor is very expensive since I need to change my pfc unit. And since I live in Norway it is not very eazy to sell used skylineparts locally =)

I was hoping there was a easy and cheap fix with paralell wiring for dual afm's =)

Do you get what he meant though?

Doesnt sound like it as it would solve your problem, and not cost much

At first I didnt understand it, but after reading it a couple of times I think I get it =) only running on MAF, and making a tune to compensate for the "false" air that runs trough the other funnel. I get it...interesting suggestion.

I need to do something like this as well. I need to run a bypass valve and re-tune my car.

I want to run 30psi and I cant because my AFM is making out at around 24psi.

I am going to either modify my AFM and remove it from the plastic pipe its in and then put it into a 4" pipe OR i will run a bypass....

Have been looking around some of the z32 forums, apparently u can run one working/one dummy maf sensor and halve the k value in the std ecu, sounds to simple. might be a little more complicated than this.

I was thinking that wiring the two in parallel to average the voltage, then halve the K value would be better.

Not sure how this equates with u PFC users out there.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...