Jump to content
SAU Community

Recommended Posts

i have not had the chance to dig around in the shed yet guys but i wil endeavour to do it tomorrow nite and see what i can find.

i have just finished a 14hr day and will be another 3 in a row the same so please bear with me k :D

cheers oxford

They're handy if it's a cold and rainy night, and the inside of the car is getting steamy 'cos the heater is on. You can open the windows slightly and not have the rain getting in.

Heat + aircon = hot dry air, no fogging up :D

hiya again all.

the part numbers from local nissan dealer and pricing are as follows.

part# NI-G3800-0V500 Description ROOF VISOR price $268.40 plus GST which works out to be $295.25.

that is what i paid for them ex-japan on the 18/6/06 at local nissan dealership, took them around 4-5weeks to get here but saved a ton on freight charges.

cheers oxford

I'm mainly after a set because I'm sick of the wind noise I get on both sides when on the highway etc. I'm guessing this is because of the pillarless door frames. For you guys that do have them does it make a difference with the wind noise etc. And yeah cleaning my windscreen and having the water comming in was a pain but my FMIC fixed that....no windscreen washer bottle :)

Edited by Mr_RS4

still get a little bit of wind noise when in a heavy wind or have turned the wick up a bit on the back roads etc :(

but all in all they are a good investment as they give a lot of other benefits too

cheers oxford

http://page18.auctions.yahoo.co.jp/jp/auction/w10673072

they sometmes come up in Yahoo auctions if you have a

means of purchasing & delivery to Australia. The price

looks good too...

I have a passenger side set only if anyone wants to throw money at me. I dunno what they are worth so PM me with an offer if ur interested. I may or may not throw in a lap dance in my new sequined mankini....

edit - *SOLD*

*FEELS CRUSHED THAT LAP DANCE OFFER WAS REFUSED...*

Hey Phil.. Was that 1.8m long measured from one end to the other, following the curve?

If they were in a box, how long do you think it would be? 1.5m?

HI

They are 1.8m following the curve or 1770mm tip to tip

To put them in a box it would need to be about 1.8m L x 250mm W x 50mm D

I could see both fitting in a box this size with a bit of packing

Hope this helps

Thanks

Phil

  • 8 months later...

Hi There,

sorry to drag up an old topic but is it hard to fit these? I have managed to secure (if I want) a set and given Im missing a drivers side and suffer the normal problems (window down water running in, in mornings and wind/driving rain leakages) I would like to grab them and fit them. The ones I can get have no clips and there seems to be nothing on the car itself. Is the mounting hardware if any common fitting clips or are they stagea specific?

Thanks for any help you all can give

Kenny

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...