Jump to content
SAU Community

Recommended Posts

Hi there guys, i need some help!! I have a r32gtr and it has aftermarket turbos injectors computer etc and i was giving it heaps in 2 wheel drive lke reving its tits off and i pulled up in the garage and popped the hood and there was oil everywhere, I freaked out and did not know what to do. I looked at the dip stick and it was sticking out a little and the oil was all around that area and the engine bay. What does this mean????

1 Maybe too much oil in the car

2 No catch can fitted

3 What happens when you rev the shit out of these engines

I dont know can anyone help me please???

Link to comment
https://www.sau.com.au/forums/topic/179827-oil-everywhere/
Share on other sites

sound like a over pressurized sump to me. 2 things would have happened, blown rings or ring landings, high reving pressurized sump but little to no damage (very lucky). chuck some more oil in her and if it is still blowing a engine rebuild is needed. could also do a compression test first.

Link to comment
https://www.sau.com.au/forums/topic/179827-oil-everywhere/#findComment-3272960
Share on other sites

Have went out and given it heaps again and it seems to be fine now, i had it serviced and i think there was too much oil put in it, can it react in this way because the car still has a little over full even after loosing quite a bit of oil, maybe 500ml of it??

Link to comment
https://www.sau.com.au/forums/topic/179827-oil-everywhere/#findComment-3273633
Share on other sites

Have went out and given it heaps again and it seems to be fine now, i had it serviced and i think there was too much oil put in it, can it react in this way because the car still has a little over full even after loosing quite a bit of oil, maybe 500ml of it??

yeah it can.. .i've never experienced the dipstick moving, but my oil was overflowing into the catchcan... over 1ltr, so it was spilling out of the catchcan... after a leak down test, it turns out one of the cylinders was less than perfect....

so i'd get it check if i was you... for me it was ONLY happening under hard right hand turns (at a track) so we wouldn't have picked up on it, if not for that!

edit: should add, i had the normal amount of oil in, so maybe it is just excessive oil for you... to be honest, its not something i'd risk... get it checked out!

Link to comment
https://www.sau.com.au/forums/topic/179827-oil-everywhere/#findComment-3273667
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...