Jump to content
SAU Community

Recommended Posts

Hey All,

Had my 32 gtr up on the hoist the other day and noticed the O2 sensor wasnt hooked up, the plug was just sitting there with no connecting plug to the loom\wire harness in sight. Im running an Apexi PFC and it seems to run fine without it, does it need to be connected though?? Im thinking I might get a bit better fuel economy if it was hooked up.

Cheers!

Gagz

Edited by R31 Gagz
Link to comment
https://www.sau.com.au/forums/topic/181265-does-apexi-pfc-use-o2-sensors/
Share on other sites

Hey All,

Had my 32 gtr up on the hoist the other day and noticed the O2 sensor wasnt hooked up, the plug was just sitting there with no connecting plug to the loom\wire harness in sight. Im running an Apexi PFC and it seems to run fine without it, does it need to be connected though?? Im thinking I might get a bit better fuel economy if it was hooked up.

Cheers!

Gagz

I think you are confusing the O2 sensors with the cat temp sensor. I would say what you say was the cat temp sensor disconnected. it doesn't matter at all. it's purely there to set off the cat temp warning light to tell you the cat is getting hot. the O2 sensors can be seen inside the engine bay from above. one in each dump pipe and it's best to have them connected for fuel economy but it's no big problem if they are disconnected and you have an ecu (like power FC) that you can tune the light load cruise area of the map.

Thanks but its definitely the O2...I know what one looks like as Ive replaced three of them in the past on other cars and I could see the unplugged cable leading straight to the O2 that was connected to my dump pipes....couldn't see it from above as Ive got two turbos and two 4" turbo dump pipes blocking my vision :)

Cheers!

Gagz

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeap, not as doorty as ITB's, but alot more doorty than before, induction sound great when I'm up it 馃
    • Any difference in induction noise?
    • I think you know exactly who I mean.
    • If I got a dollar for every flipped commuter missile I've driven past I'd have two dollars   Some people get into wild adventures on the road and I doubt it's gender or ethnicity specific. I'm just glad I don't usually drive during peak times.
    • Just got the car back and gave it a good run back home Power wise, whilst it only made a extra 5 killerwasps up top at 7200 rpm, it made more power everywhere from 2500 rpm and kept pulling much harder all the way, to the point of me relearning when to shift so I don't hit the 7200 limiter, with the old intake it seemed to take alot more time to rev out, and, throttle response is also much improved  As I didn't want to remove the bumper every time I serviced the air filter (basically every aftermarket and fabricated CAI has the filter behind the bumper) it currently has a hektic exposed pod in the engine bay sucking in hot air, this will be rectified shortly after some some of my CAD (cardboard assisted design) for a alloy heat shield feed by the OEM intake tube behind the bumper, this will cop some wrinkle black paint, as well as the intake pipe for that totally OEM look... The only fly in the ointment was that the OEM "strut" brace doesn't fit over the rear runner of the new intake with the 2.5 engine is in the engine bay, as the 2.5 raises the engine up by 20mm, it's not a war stopper, and I didn't notice any difference without it in some twisties, but....... MX5 Mania is bringing in some GWR "fancy pants" braces that apparently do fit, if it bolts up I'll grab it, it is also stiffer than the OEM one, which is a bonus All in all I'm happy with the outcome      Fancy pants "strut" brace that gives the required clearance      This is where the clearance issue was, the GWR extends out past this
  • Create New...