Jump to content
SAU Community

Recommended Posts

do a search in forced induction this question has been asked about 20million times

yeah, with a million different and rather generic answers

i'm looking at boost controllers right now infact, the 3 on my list are:

greedy profec b spec II

apexi power fc boost controller kit, and

Blitz SBC Spec R - Dual Solenoid

going through all the pros and cons of them, i think the power fc add on might win because i really dont want controllers sitting in the car

but the summary from the threads on SAU is that the blitz dual solenoid controllers are the best and hold boost the best (the spec r is the entry level controller for that range)

and the greedy is sitting on top of my list because i asked shaun from boost worx what he would recomend, and this is the one!!

i think its going to come down to the greedy vs apexi, i just want some more information on them first =)

hope this helps

Edited by Fishpaste~
Link to comment
https://www.sau.com.au/forums/topic/181781-ebc/#findComment-3301571
Share on other sites

do a search in forced induction this question has been asked about 20million times

The main point was to see what guys from Adelaide use, not so much which is better, just threw that in so the thread isn't too boring.

pfc

btw, arent u selling ur car?

Yeh its not for me, its just i was discussing it with a friend and wanna see which ones get used the most.

Fishpaste, what about EVC 6 ?

Link to comment
https://www.sau.com.au/forums/topic/181781-ebc/#findComment-3301586
Share on other sites

ok i use an avcr, its unreal great for higher power applications in its ability to be able to control boost per gear by rpm etc etc. The pfc kit is a waste of money for what it is unless you can get one cheap, all you can do it select one boost and thats it you cant control the duty etc etc.

Edited by sinistagtst
Link to comment
https://www.sau.com.au/forums/topic/181781-ebc/#findComment-3301676
Share on other sites

I agree Dan, having used the AVCR on my previous ride I will say it was better but when I got my car it already had the PFC boost controller kit on it so I saw no point in changing unless I want to chase higher power levels (who doesn't though, right :) :))

Link to comment
https://www.sau.com.au/forums/topic/181781-ebc/#findComment-3301723
Share on other sites

avcr here, so far so good after Dan installed it for me. How's them beer's?

will know more of how it performs after my tune but after fiddling with it and reading the aussie manual for a while the other night i'm very impressed with all the features it has!

Link to comment
https://www.sau.com.au/forums/topic/181781-ebc/#findComment-3302113
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...