Jump to content
SAU Community

Recommended Posts

They must have changed the design slightly, i fitted one quite a while ago and didnt have the fitting underneath for the auxilliary air valve to plumb in so i didnt use it, managed to just use the idle motor, lucky it ran haltech i guess.

thanks mate from Georgia!! I have bought intake few days ago but firs when i see it i guess that instalation is impossible and there is some mistake ore seller send me other manifold:) again thanks for post and if i will have some problems while instalation i will ask you few advice:)

THANKS THANKS THANKS

  Lazy-Bastard said:
re-route the BOV return piping to your new BOV if it's a plumb back. If it's an atmo venting BOV then block the return.

Thanks ...

Please help me

i have installed plenum but have some problem i think i have mistake with pipe connectorsto plenum in nautral rev all times goes up and down i dont know why and i have all time minimal rev 1100 RPM

please can someone help me? it would be grat if you can put the pictures what to connect to the plenum, i thing my problem is in that actually

thanks and waiting for some info:(

Edited by guricha

plenuminstall20048.jpg

guys does anyone know what will be consequence if on hight boost this wire will be blocked suddenly??? can it give some detonation ore can damage turbo???

please help me again:)

  • 1 month later...

i started this modification on monday just been spending afternoons working on it, but its nearly finished, just gotta redo the piping and extend the 2 wires for the acv

pics before n after below

i found a few extra steps i had 2 take that werent in the DIY

btw was there a reason why u put ur injectors in upside down? which explains why u had to spin ur fuel reg around?

post-29137-1197465343_thumb.jpg

post-29137-1197465386_thumb.jpg

post-29137-1197465420_thumb.jpg

Yeah, I spun the injectors around so that I could get the wiring harness clipped onto each one easier. If you notice in your pic, they are hard-up against the throttle intake runners. I just wanted to make it look a bit neater really.

yeah mine still clipped on easy enough

i dont like the throttle cable setup though:S wont be long before it snaps i rkn

i still havent plumbed up any of my cooler piping or my acv hose but car drives sweet as

response is unreal lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Kinkstah, no, coilovers aren't illegal, especially as a bolt straight in. The illegal part will be if they're altering suspension geometry beyond factory limits, or the ride height is not legal.   Sounds like the blue slipper just didn't want to deal with any later possibility of mods appearing on the car.
    • The problem has always been that coilovers are able to be adjusted, almost at any time, to be too low. Most people who ever get/got defected for/with coilovers were actually afoul of the minimum ride height rule. So the interpretation by cops/inspectors was always that it is pointless to allow numpty to raise his coilovers and get the car inspected/cleared, then just drop them back down again as soon as they get around the corner from the inspection station.  This led to the interpretation that they were illegal unless rendered such that they can't be adjusted (ie, collars welded to the body, that sort of thing). That may or may not have ever actually been the official line, but I'm pretty sure it's not considered to be a solution these days. Coilovers themselves fall under clause 3.2 b of that manual, because they are an "installation of a variable ride height system" and they don't fit the exclusions in that clause (which point to air springs and other pneumatic adjusters). So, as per previous statements, they require engineering cert to be legal on the road. Once you have such cert, provided you do not adjust them outside the height range covered by the cert, you are OK. Without, you have an unroadworthy vehicle.
    • Here E10 is the cheapest fuel. And general advice is to not use it unless you hate your car. From what I remember it clogs up stuff in the fuel system or injectors?  With US/Canada being E10 across the board, does that mean that all fuel there is terrible?
    • Sorry, are coilovers ACTUALLY ILLEGAL in NSW? They aren't in Vic, as long as they retain 70% of stock travel and the car is above 100mm off the ground. Does NSW actually have a law making coilovers actually illegal? RWC/Blue Slip/Engineering people not knowing the actual f**king laws boils my blood. Demand them to point to the documentation that states a coilover is illegal. (it may exist in NSW ) Edit: I checked. They aren't. https://www.nsw.gov.au/sites/default/files/2021-02/RMS-infosheet-light-vehicle-modifications-manual-suspension-and-ride-height.pdf
×
×
  • Create New...