Jump to content
SAU Community

Cruise Alice


Sklyn
 Share

Recommended Posts

im not having a go at anyone, just exasperated...

its the same style as the one in alice but its in-ground, same brand too i think (dyno danamics)

ahwell whatever, it still pulls like a teenager

Link to comment
Share on other sites

andrew stop drunk posting. that goes for facebook too... well the best time i could get with a G-Max (if thats what its called) was 14 seconds... im not in alice anymore craig, i guess i should get off this forum then lol

Link to comment
Share on other sites

andrew stop drunk posting. that goes for facebook too... well the best time i could get with a G-Max (if thats what its called) was 14 seconds... im not in alice anymore craig, i guess i should get off this forum then lol

I did have somethig very inteligent and constructive to say but I was to drunk so that seemed easyer

Link to comment
Share on other sites

Martin, i did read that the Adelaide track is getting resurfaced for them to have a strip again, in a plan to keep some street racing to a min. Should be good :)

Link to comment
Share on other sites

Would be interesting to see the difference between two Adelaide dyno's. Just don't tell them you've have it on a couple. Maybe tell them you've not long had the car and wanted to get a power figure and tune checked.

Link to comment
Share on other sites

If anyone knows someone looking for a car i would be interested in moving my Sil80 (180sx with s13 front). has a recon motor, new turbo, bigger fuel pump plus a few other bits and peices, needs a bit of work but a good project or drift/drag car on the cheap. made 180kw on a base tuned computer

Link to comment
Share on other sites

  • 2 weeks later...

Leigh,

go to MRT and go buy the Front diff spool and make it RWD for the night. Take around 2-3 hours and some gearbox fluid and your in rear wheel mode :D

Link to comment
Share on other sites

its a bit slow in here huh???

im lacking motivation to get my car running again. need to put the fuel tank back in and get a gearbox.

i also started to pull my dash apart to fit my gauges but dont have the tools at the moment to finish it.

whats everyone else doing?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • 215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...