Jump to content
SAU Community

Recommended Posts

I would like to know ( if others already havent asked )Why the change of name to Swiper the Fox from Dirtgarage ? And why lose the cool avatar to be replaced with some cartoon fox ?

No real reason...i just did it because my daughter likes the character. Swiper no swiping! Ohh mann!

Your too late...you will never catch me now!

on topic

Edited by Swiper the Fox
  • Replies 682
  • Created
  • Last Reply

Top Posters In This Topic

Maybe a Motec for this one :nyaanyaa:

Nah still Vi-pec...Jim says its doing the job just fine. Would work better with proper crank trigger instead of factory CAS over 9500rpm. But up to 9500 the vi-pec is doing a stellar job....makes 25psi instantly on the anti-lag at 7000rpm with 25deg out of it.

the MoTeC is for the new car. :nyaanyaa:

Nah still Vi-pec...Jim says its doing the job just fine. Would work better with proper crank trigger instead of factory CAS over 9500rpm. But up to 9500 the vi-pec is doing a stellar job....makes 25psi instantly on the anti-lag at 7000rpm with 25deg out of it.

the MoTeC is for the new car. :D

The car performed reasonably well at a closed test session at Sydney Dragway on Monday...most of the day was spent trying to get some reliable data out of the car and testing the new suspension. On the first full pass it easily ran 10.1 @ 140 with quite a large lift-off straightening the car at the top of 1st gear with the data telling us the car lost around a second. Its got a lot more torque now and is a bit of a handfull but further suspension tweaks this week have the car running straighter instead of trying to drive me into the wall. Full day at CRD today perfecting the set-up so its a little easier on the driver and installing a few more goodies in the car.

Big thanks to Jim and Con at CRD who have worked tirelessly on getting it ready for the 28th.

Edited by Swiper the Fox
Good to hear that CRD have come to the party rregarding track assistance, im sure there is some knowledge to be gained by all parties.

CRD's commitment to the car knowing that there is just one event to get it right is incredible.

Opened the shop so i could work on the car all day today. Jim made up a list of what he requested to be installed/changed and with the help of a mate we got to work. Still quite a bit to do with only a week to go...but we are determined to get the car 100% before Sunday.

Their additude and professionalism is of the highest standard...a real pleasure to work with.

Look forward to seeing it in action on the 28th & hope it will all come together for the magic number on its last hurrah..so to speak.

I think you more than deserve it considering the amount of time/ money/r&d that goes into chasing the numbers..i know to well what thats like.

For such a dedicated to the drag scene guy like yourself over the years, i hope you nail it on the day...everyone knows its true potential .:)

CRD's commitment to the car knowing that there is just one event to get it right is incredible.

Opened the shop so i could work on the car all day today. Jim made up a list of what he requested to be installed/changed and with the help of a mate we got to work. Still quite a bit to do with only a week to go...but we are determined to get the car 100% before Sunday.

Their additude and professionalism is of the highest standard...a real pleasure to work with.

Paul, is there anyone else :blush: I mean, in many ppls eyes jim is the best tuner and has A LOT of experience!

How many runs will u get on the day?

Paul, is there anyone else :) I mean, in many ppls eyes jim is the best tuner and has A LOT of experience!

How many runs will u get on the day?

Here's a little something i knocked up today...weighs a ton! and used 2 meters of 6mm x 200mm flat bar (mild steel) But its minimum legal size so can only trim the mounting tabs after trial fitting.

From ANDRA General Regs

4.2.6 Flywheel Shields / Bell-housing

All other clutch equipped cars running quicker than 11.00 (1/4 mile) / 7.00 seconds (1/8 mile) are required to use a steel or titanium bell-housing or shield. A totally enclosing 360 degree, one-piece bell housing must be formed or fabricated entirely from 6mm (1/4 inch) steel plate and attached directly to the rear of the engine. Where used, flywheel shields must be constructed so they completely surround the clutch failure. The shield should be constructed from 6mm (1/4 inch) steel plate, and extend forward to a point at least 25mm (1 inch) ahead of the flywheel, and 25mm (1 inch) to the rear of the clutch and pressure plate. Shields must not be bolted to the bell-housing and should attach securely to the frame /chassis. All shields or bell-housings must be removed from the vehicle for checking during the Technical Inspection. An engine support strap made of steel or aircraft cable (chain not accepted) capable of supporting the rear of the engine in case of bell-housing failure is required on all cars, unless it is evident that the headers or frame rails will prevent the engine from dropping.

Be aware that Ballistic Blankets are NOT legal.

post-23582-1269355404_thumb.jpg

Edited by Swiper the Fox

Holy shit Paul,

All because some f**kwit had a cast flywheel explode.

what a mission but hey its done now.

A titanium can for a doorslammer is $5000 but you can only buy one to suit a lenco so the way paul has done it is the only way.

All because some f**kwit had a cast flywheel explode.

Yeah in 1985...

The rules havnt been revised in 25years...

Nice hoop paul. You going to sell it when you part it out??? ha ha ha

ANDRA is going to have to review they're rules and regulations if they plan to stay viable in the next 10 years. As an organisation, they turn away from anything new: Vehicles, technology, good buisness practice.

As the "Import" generation gets older, we're bound to spend more time and money on racing... Why can't the ANDRA see that?

It's not just "imports" but all modern hi-po cars on the drag strip.

Maybe we all should start supporting "independant" drag facilities... Or private test sesions on air-strips- Standing mile, style of thing.

Yeah in 1985...

The rules havnt been revised in 25years...

Nice hoop paul. You going to sell it when you part it out??? ha ha ha

ANDRA is going to have to review they're rules and regulations if they plan to stay viable in the next 10 years. As an organisation, they turn away from anything new: Vehicles, technology, good buisness practice.

As the "Import" generation gets older, we're bound to spend more time and money on racing... Why can't the ANDRA see that?

It's not just "imports" but all modern hi-po cars on the drag strip.

Maybe we all should start supporting "independant" drag facilities... Or private test sesions on air-strips- Standing mile, style of thing.

It would cost you more in freight than to build it...lol.

Ill send you the final drawings and material list/sizes once the design is perfected...the above is only prototype but will get me through scruiteneering this weekend.

It would cost you more in freight than to build it...lol.

Ill send you the final drawings and material list/sizes once the design is perfected...the above is only prototype but will get me through scruiteneering this weekend.

That would be super handy...

(for my titanium hoop)Bah ha ha ha... I'm so funny. Steel, blaaa.

Here's a little something i knocked up today...weighs a ton! and used 2 meters of 6mm x 200mm flat bar (mild steel) But its minimum legal size so can only trim the mounting tabs after trial fitting.

From ANDRA General Regs

4.2.6 Flywheel Shields / Bell-housing

All other clutch equipped cars running quicker than 11.00 (1/4 mile) / 7.00 seconds (1/8 mile) are required to use a steel or titanium bell-housing or shield. A totally enclosing 360 degree, one-piece bell housing must be formed or fabricated entirely from 6mm (1/4 inch) steel plate and attached directly to the rear of the engine. Where used, flywheel shields must be constructed so they completely surround the clutch failure. The shield should be constructed from 6mm (1/4 inch) steel plate, and extend forward to a point at least 25mm (1 inch) ahead of the flywheel, and 25mm (1 inch) to the rear of the clutch and pressure plate. Shields must not be bolted to the bell-housing and should attach securely to the frame /chassis. All shields or bell-housings must be removed from the vehicle for checking during the Technical Inspection. An engine support strap made of steel or aircraft cable (chain not accepted) capable of supporting the rear of the engine in case of bell-housing failure is required on all cars, unless it is evident that the headers or frame rails will prevent the engine from dropping.

Be aware that Ballistic Blankets are NOT legal.

should have knocked it up in balsa wood and painted it :cool:

Here's a little something i knocked up today...weighs a ton! and used 2 meters of 6mm x 200mm flat bar (mild steel) But its minimum legal size so can only trim the mounting tabs after trial fitting.

From ANDRA General Regs

4.2.6 Flywheel Shields / Bell-housing

All other clutch equipped cars running quicker than 11.00 (1/4 mile) / 7.00 seconds (1/8 mile) are required to use a steel or titanium bell-housing or shield. A totally enclosing 360 degree, one-piece bell housing must be formed or fabricated entirely from 6mm (1/4 inch) steel plate and attached directly to the rear of the engine. Where used, flywheel shields must be constructed so they completely surround the clutch failure. The shield should be constructed from 6mm (1/4 inch) steel plate, and extend forward to a point at least 25mm (1 inch) ahead of the flywheel, and 25mm (1 inch) to the rear of the clutch and pressure plate. Shields must not be bolted to the bell-housing and should attach securely to the frame /chassis. All shields or bell-housings must be removed from the vehicle for checking during the Technical Inspection. An engine support strap made of steel or aircraft cable (chain not accepted) capable of supporting the rear of the engine in case of bell-housing failure is required on all cars, unless it is evident that the headers or frame rails will prevent the engine from dropping.

Be aware that Ballistic Blankets are NOT legal.

my mate used to be a mechanic at ford muscle parts in syd & he told me some horror stories of old gt's with big hp where the flywheel has come off & sheared right through the tunnel & floor pan (imagine if it connected with the drivers legs)

my mate used to be a mechanic at ford muscle parts in syd & he told me some horror stories of old gt's with big hp where the flywheel has come off & sheared right through the tunnel & floor pan (imagine if it connected with the drivers legs)

Thats why balsa wood is such a good idea.

780034fu9.jpg

780050oh0.jpg

780039wy7.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...