Jump to content
SAU Community

Recommended Posts

as iain said.

its not easy to access either, my assumption the whole side wall needs to come out unless you have spiders legs for fingers...

what were you trying to do??

Well my 4WD light is on and I have done the MIL light diagnostic and got 0000 so I thought I would move on to the Altessa computer as it directly controls the 4WD. Some of the C34 guys spoke about a diagnostic program for the altessa that works for them, not sure if there is one for the M35. Also want to check that everything is wired up properly.

Mike.

fair enough..

The Attessa ecu in the C34 is easier to get to than ours.. from memory.

Be prepared to pull off the whole inner wall in the boot to access it.

If you take the drivers side "compartment" out (just a couple of clips, it pulls right out) you can just barely see the Attessa comp sitting there. what i notices is that the plug is on the bottom side, and i think i could only see one of the bolts holding the ecu..

theres a couple of plugs directly below it under the car if you take the vented tray off, maybe check those wires too.

So I don't think there are any M35's in Tassie, certainly none for sale. So last night I test drove a 97' Stagea. It was probably the most under-whelming experience driving a car I've ever had. What is with the extremely loud fan sound from 0-50? I booted it a couple of times and it felt like I was going 200k's an hour yet I was slowly creeping past 20, on my way to 50 which took about 4 hours. I wasn't expecting GTR performance but this thing performed like a VAN and that is no exaggeration. There was also a loud high pitch 'pulley or belt sound in the upper rev range. It was actually a frightening experience cause every time I accelerated it felt like I'd blown the car up. I remember driving my old man's EL Falcon wagon and that was far and away superior to this thing. It felt draconian.

TELL ME IT WAS JUST A BAD EGG OR TELL ME IT WASN'T BUT THE M35'S IS FAR SUPERIOR.

So I don't think there are any M35's in Tassie, certainly none for sale. So last night I test drove a 97' Stagea. It was probably the most under-whelming experience driving a car I've ever had. What is with the extremely loud fan sound from 0-50? I booted it a couple of times and it felt like I was going 200k's an hour yet I was slowly creeping past 20, on my way to 50 which took about 4 hours. I wasn't expecting GTR performance but this thing performed like a VAN and that is no exaggeration. There was also a loud high pitch 'pulley or belt sound in the upper rev range. It was actually a frightening experience cause every time I accelerated it felt like I'd blown the car up. I remember driving my old man's EL Falcon wagon and that was far and away superior to this thing. It felt draconian.

TELL ME IT WAS JUST A BAD EGG OR TELL ME IT WASN'T BUT THE M35'S IS FAR SUPERIOR.

Strange. C34's usually go pretty good for a wagon. The one you drove must be in bad need of a service etc.

Of course M35's kick arse and chew bubble gum. (and I'm all out of gum)

IMHO the M35 is a comfortable cruiser, but can go pretty hard if you push the loud pedal. It's quiet and has a fair bit of room.

Much the same as the C34!

So I don't think there are any M35's in Tassie, certainly none for sale. So last night I test drove a 97' Stagea. It was probably the most under-whelming experience driving a car I've ever had. What is with the extremely loud fan sound from 0-50? I booted it a couple of times and it felt like I was going 200k's an hour yet I was slowly creeping past 20, on my way to 50 which took about 4 hours. I wasn't expecting GTR performance but this thing performed like a VAN and that is no exaggeration. There was also a loud high pitch 'pulley or belt sound in the upper rev range. It was actually a frightening experience cause every time I accelerated it felt like I'd blown the car up. I remember driving my old man's EL Falcon wagon and that was far and away superior to this thing. It felt draconian.

TELL ME IT WAS JUST A BAD EGG OR TELL ME IT WASN'T BUT THE M35'S IS FAR SUPERIOR.

I had the same experience as you with the C34....must have been a bad egg as well........I have driven an 260 and found it pretty good....but no GTR!.....M35's are completely different to drive....much more of a cruiser.

So I don't think there are any M35's in Tassie, certainly none for sale. So last night I test drove a 97' Stagea. It was probably the most under-whelming experience driving a car I've ever had. What is with the extremely loud fan sound from 0-50? I booted it a couple of times and it felt like I was going 200k's an hour yet I was slowly creeping past 20, on my way to 50 which took about 4 hours. I wasn't expecting GTR performance but this thing performed like a VAN and that is no exaggeration. There was also a loud high pitch 'pulley or belt sound in the upper rev range. It was actually a frightening experience cause every time I accelerated it felt like I'd blown the car up. I remember driving my old man's EL Falcon wagon and that was far and away superior to this thing. It felt draconian.

TELL ME IT WAS JUST A BAD EGG OR TELL ME IT WASN'T BUT THE M35'S IS FAR SUPERIOR.

I'd say it was a bad egg if it was making those kind of noises...

... having said that, I drove a number of Series 2 C34's prior to buying my M35 and was completely underwhelmed with them also (as was the wife!).

Never drove a Series 1 C34, but considering lower power/torque figures and 1 less gear I don't think I needed to.

Love my M35. They are indeed far superior.... I just wish they could tow like a C34 can :(

yeh agreed. i fkn hate my car right now. but still prefer it to the C34.. driven a few when i was looking for the m35 and just wasnt impressed. drove the m35 and i felt a whole heap stronger.

Did you have a drive of a 260?....only reason I didn't buy one was that it was a 2000 model....to old for me :P

yeh i drove a 260. actually liked them and the only reason i didnt get one was because of the P plates at the time..

m35 is much more soothing to a police officers eye.. accept for the cunt that shoved a stick up the exhaust 4 days ago..

Ah ok, I just checked, I didn't realise the series 1 only had 170kw. Not a lot of power for a big car. Makes a bit more sense now. Still, it was an abysmal experience. I'm test driving a manual legnum next week with the AYC. See how that goes.

If that doesn't impress me then I'll be in search of a M35 on the mainland. From the advice I've got on here, something with upgraded suspension would be nice. I might be waiting a while, I want an M35 with all black interior (inc black heated/adjustable leather seats) & the VDO in very good condition however i'm not willing to pay over $14500. I've seen a couple go for this price, so it's just a matter of being patient.

Just a pain in the ass I can't test drive one down here before I fly over.

Nah I've seen a few go with those options for that price. Australia isn't in great shape atm, houses are on the market for twice as long as what they were 4 months ago, the reserve bank hasn't put interest rates up for some time because consumer spending is poor. Furthermore, they're coming up to a decade old now. You can get a 2001 Audi Allroad twin turbo V6 for around 16-18 which were 100k priced new.

When all said and done, al ot of people selling cars all start off 25-30% more than what they eventually get and this site is a perfect example of it. Not until they go below 16 are they selling, yet they all start between & 18-20, then it's "bump down to 17500" 1 month later "bump down to 16000" then another couple of weeks "bump down 14000" et etc.

In this market, the buyer is king.

I'm a perfect example of douche trying to get what he thinks his car is worth. I initially advertised my car so that it was equally the best buy on carsales which was 14k. Had I just advertised it for 12500 (well below market) I would have sold it 6 months ago but now i'll probably get even less than that

IMO 14500 evaluation is quite generous.

Yeah, sorry mate; I'm with zei20l on this one.yes.gif

Excellent condition all round, and Cheap are mutually exclusive concepts.

The guys in this forum are a great resource, and are helpful to a fault; it would pay you to take it on board.

The M35 is not a car you want to skimp on price. It will bite you on the arse, HARD.

Re; Allroad; you do not even want to know what they cost to repair and buy parts for...

Edited by Daleo

so buy an audi lol

and if you re-read my post, i said you wont find anything in the condition you describe for that price. youll get something with over 100k on the clock for under 14k

Lol I don't want to spend that much on a car (as I said I want to spend no more than 14500). I'm going to purchase a couple investment properties in 8-12 months ... if I did want to spend 17-18, yeah i'd be all over an an Audi Allroad.

You raise an interesting point re condition and kilometres. K;s have always been 'a big ticket item' for me but they seem less important when importing a car due to the increased risk that the K's have been wound back. I gotta say, you're pretty much the scum of the earth if you wind back the k's on a car, right down their with peod's and the like.

From people have said on here, it's better to get a car that's in good condition with higher k's than a car in average condition with lower k's

Re: Condition - yeah I'm arguing I can get all the options and vg condition for less than 15.

Only one way to find out thumbsup.gif

well, post up when you get one :)

you generally pay a little more for a better coonditioned car. and i rekon if youre not buying one FOB then it will have over 100k on the clock. not that its a bad thing, people have over 200k on the original motor and its still going fine

The M35 is not a car you want to skimp on price. It will bite you on the arse, HARD.

Re; Allroad; you do not even want to know what they cost to repair and buy parts for...

agreed x 1000

he already owns an alfa, he knows how much servicing on a euro costs.

Yeah, sorry mate; I'm with zei20l on this one.yes.gif

Excellent condition all round, and Cheap are mutually exclusive concepts.

The guys in this forum are a great resource, and are helpful to a fault; it would pay you to take it on board.

The M35 is not a car you want to skimp on price. It will bite you on the arse, HARD.

Re; Allroad; you do not even want to know what they cost to repair and buy parts for...

Fair point

Re: Getting bitten on the arse: Any car I buy will be tested by a certified inspector AND taken to a panel beaters for an inspection on whether it's been in an accident. I do that both with private and car-yard sales.

If I do that and still get bitten on the arse well so be it, not much else I can really do eh

I honestly think it's a matter of patience and I don' think that premise is any different for any car you buy.

As for parts, i've owned a couple of Alfa's in my time, nothing would shock me lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...