Jump to content
SAU Community

R34 Rb25det Neo Vs. R33 Series 2 Rb25det

pricer-1

By pricer-1,
in Engines & Forced Induction

 Share

Recommended Posts

pricer-1 Rookie

pricer-1

Posted
Posted

So I have been looking into a RB swap for my S13 and I think I want to go with the R34 Neo but I have a few questions about differences between the Neo and Series 2 engines. When it comes to upgrades or even just OEM parts will the parts for a Series 2 motor work on a Neo? Physically what are the differences? Also what parts should I consider replacing before installing the engine into my S13?

silverr34gtt Enthusiast

silverr34gtt

Posted
Posted (edited)

Theres plenty of neo specific head upgrades like poncams and fine tune timing belts ect. the stock rb25 neo has superior torque and power to the earlier rb25 also.

Parts to replace. Might want to look at a set of splitfires, i had problems with standard coilpacks failing. Other than that i cant think of anything, unless u want to go for extra power. :nyaanyaa:

Edited by silverr34gtt
pricer-1 Rookie

pricer-1

Posted
  • Author
Posted
Theres plenty of neo specific head upgrades like poncams and fine tune timing belts ect. the stock rb25 neo has superior torque and power to the earlier rb25 also.

Parts to replace. Might want to look at a set of splitfires, i had problems with standard coilpacks failing. Other than that i cant think of anything, unless u want to go for extra power. :thumbsup:

I have seen a lot of people talking about replacing the water pumps, oil pumps, time belt, timing belt tensioner and idler pulley, etc bc the engine is most likely coming from a junkyard and has been sitting for a while. Do you think it is all necessary precautions?

Dale FZ1 Veteran

Dale FZ1

Posted
Posted

Water pump, timing belt + idlers, crank + cam seals, various water hoses. From the viewpoint of ensuring absolute reliability in those areas - YES. Oil pump as a service issue though, I doubt it.

Some of the parts aren't particularly cheap, but if you consider the time + labour factor involved once an engine is in the car, it is a smart option while the engine is sitting on the bench/workshop floor.

RB30-POWER Mentor

RB30-POWER

Posted
Posted

Both type of Rb25DET engines have same static compression ratio. 9.0:1

Rb25DET Neo has same turbo as series 2 R33 RB25DET, but has the larger (OP6) exhaust turbine housing. Same housing as used on the VG30DET. (Single turbo engine)

Col-GTSX Grand Master

Col-GTSX

Posted
Posted

Honestlly the Neo motor is going to be younger, so it would be the better option...

However that said some second hand Neo's can be rather expensive compaired to theolder S2 rb25, so I guess you just need to weight it up...

But on the solid lifters alone id be buying a neo motor...

  • 2 weeks later...
GOLD_JET Contributor

GOLD_JET

Posted
Posted

it somes with hks fuel rail bigger injectors, fuel reg and better coil packs. i have a good turbo so prob just a computer and i guess i would be happy for a while. but just wanna no. some people say s2 25 is the best and some say neo. just real confusing. dont wanna get the wrong one hahah

R338OY Veteran

R338OY

Posted
Posted

Go for the better, newer Neo if you can afford it.

S2 RB is great engine too, and will be cheaper to buy and probably cheaper to mod (if thats the plan), but it's not as advanced as the R34 Neo.

The Neo is more enviromentally friendly. Guess that's not important on this forum :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...