Jump to content
SAU Community

Recommended Posts

Hi guys,

I'm after a bit of advice, I have an r32 gts-t (93), I have noticed my factory oil pressure guage reads quite low (nearly back to 0 on idle, and only just above 2 for normal driving), is this likely to be an oil press sender issue? It runs fine, plenty of oil etc...

Also another quick question, I occasionally get a small hesitation when I roll off and back on the throttle, as in, I back off slightly, and then when I squeeze the pedal back on it gives a small miss, and then pulls away fine, not the end of the world, but it never used to do it.

Any help would be great!

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/186241-r32-oil-pressure/
Share on other sites

Hi guys,

I'm after a bit of advice, I have an r32 gts-t (93), I have noticed my factory oil pressure guage reads quite low (nearly back to 0 on idle, and only just above 2 for normal driving), is this likely to be an oil press sender issue? It runs fine, plenty of oil etc...

Also another quick question, I occasionally get a small hesitation when I roll off and back on the throttle, as in, I back off slightly, and then when I squeeze the pedal back on it gives a small miss, and then pulls away fine, not the end of the world, but it never used to do it.

Any help would be great!

Cheers.

Oil pressure Sender units are notorious for giving up the ghost, have someone check your oil pressure with a mechanical gauge. Flat spots are generally caused by a lean mixture, you may have an air leak into the inlet manifold.

  • 2 weeks later...
...I have noticed my factory oil pressure guage reads quite low (nearly back to 0 on idle, and only just above 2 for normal driving),

I notice the exact same thing with mine, could it be normal for a R32 GTS-T. My oil pressure does however rise to 4 after it has fully warmed up though.

My motors healthy (compression tested etc..) but the oil pressure gauge always reads low.

On start up when cold it will be just under '4' on the stock oil pressure gauge, and it only gets lower as it gets warmer.

When cruising at a consistant speed its quiet low, but at about 100km/3XXXrpm its in between '2' & '4'..

I don't really worry about it to much as I have been told the stock oil pressure gauge is useless, so I won't be able to get an accurate reading till I get a decent after-market oil pressure gauge.

i also notice the guage gets lazy around oil change time(5000kms)

Yeah mine went heaps low after I serviced it.

Was slightly worried with it being so low..

Edited by abu

Hi again all,

Well I have fixed the problem, turned out to be an interesting one!

I had just replaced oil and filter before I started having this problem, and I used penzoil 10w30, which was a mineral oil, and as I read some of the posts is not the stuff to use, so I went to supercheap and got some fuchs 10w30 synthetic and chucked that in just to be safe.

Took her for a drive, and to my surprise, oil pressure is now back to normal readings on the guage! Not sure how that works being the same viscosity of oil and all, but thats how it hapened!

Cheers,

Rosco.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
    • FYI: Racebox RE7R Custom Tunes Released!   https://goracebox.com/.../2017-infiniti-q50-q60-re7r-tcm...   FOR GEN 2 (21+) VEHICLES, PLEASE SEE NOTE AT BOTTOM See more   But whomever tuned your car is the tuner you should go back to, AMS, Sonictune or BT Tune....
×
×
  • Create New...