Jump to content
SAU Community

Recommended Posts

omfg. instant hardon... I want one...

-D

mmmmmmm garage porn..lol

needs the mandatory tire posters and snap on tools posters with half nude girlies..lol,,, and the keg bar fridge and couch for mates parties after hours.lol

they could leave the GT3 in it for me too..lol

*long winded explanation*

I've already added a cusco brake cylinder brace and braided brake lines and those two improve the feeling/response of the brakes quite a bit. The new rotors should really seal the deal, I can't see myself needing bigger calipers or disc diameter...

-D

I researched the brake cylinder stopper a bit today, and had responses from "nope, dont bother on a street car, no difference" to "wow i felt the difference straight away!" I guess with more rigidity in the cylinder your always going to get a better pedal feel.

Well just got my car back with some new goodies on, she's sweet as! Props to Andrew (Blue32) for the help and Pete (SLED) for the parts :P

I'm off to bed, night all :laugh:

nice work Luke, let me no when ya free n we'll go for a boost

fk fk fk, i got mass missfire!! halp!

upped the boost to 11 today, stock turbo, hybrid front mount, 3.5" trust cat back, wrapped coil packs in insulation, re-gaped plugs to .8mm and get a few flat spots from 5 - 6.500 rpm.

anything else i can do apart from new coil packs and ecu management?

i was hoping it wouldn't be anywhere near as bad... think I might put off dump pipe and high flow cat till i get a piggyback or remap :P

dont even bother with new coils Marko.

ecu

recommendations?

full house (the car is auto sadly so pfc is off limits...)

piggyback

remap

???

note, i don't have a lot of money to play with atm saving up for paintjob.

Edited by tx3_90
Mate i would be putting my money on coil packs

Whack it on the dyno and you will find the reason in about 5 minutes

haha yeah i thought the coil packs would be rooted after so many years in a very hot place. however in saying that ill give insulation silicone a go first. If it holds 10-11psi without misfiring ill be happy, saves me $500 till i really need it (i hope). not planning on going any higher than that for a while.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
×
×
  • Create New...