Jump to content
SAU Community

Recommended Posts

Ok so this is from my 260RS diff (LH Side). Does anyone recognise it from something else?

OutputFlange01.jpg

OutputFlange02.jpg

OutputFlange03.jpg

DIMENSIONS :

31.5mm diameter across splines

33mm diameter across middle section

35mm diameter across base of shaft

Spline section is about 40mm across the overall shaft length

31 teeth

155mm long overall

Does anyone by any chance have an R32 GTR or R33 GTR they can check?

It doesn't need to be the 6 x 1 flange as I'll change axles anyway. Basically I need to figure out the LH side so I can change both or find a RH side as I simply don't have it. This is so I can match the rear diff with the front 4.111

I am trying to avoid having to change my rear hubs to GTR

Thanks

Link to comment
https://www.sau.com.au/forums/topic/189737-260rs-diff-query/
Share on other sites

260RS diff is R33 GTR diff. So are the axles.

The only R33 GTR diff I had to compare against was an Active Differential type (which was definitely different) so you could well be right. To be honest I had always assumed that 260RS was R33 GTR but I suppose R32/R33 output flanges could be the same.

Ive smashed my front diff (rear is still good) so you might want to look at that too.

I'm already running the 260RS front diff, hence why I need to change the rear to match it.

R32 GTR output flange is close enough that I could probably use it. On a whim seeing as they are also R230 I tracked down some 300ZX TT output flanges to compare against, as you can see they're quite a bit different again

media1.jpg

Dammit. I meant to say output shafts the same, not the axle shafts... My bad, sorry.

Oh ok, so I need R33 GTR output flanges then, thanks for that ;)

EDIT : I can confirm that yes they have the same part number. Cheers Psy

On the subject of R33 GTR. Can I use this :

media1-1.jpg

Its an active differential. These apparently came out in some R33 GTS25T's aswell. Has anyone ever retro-fitted one of these to there Skyline/Cefiro etc. Can anyone forsee any problem?

Edited by tRUkbOY

Well I have it all sorted now, my R33 GTR RH Output flange is on its way from Japan.

On top of that I sorted my axles and I don't need to change my hubs to GTR/260RS spec either. In case your wondering, no I am not going to use my piddly RS-Four axles nor am I using axle/diff adapters.

It was (in the end) all very easy. If anyone is interested I'll update with photos when my Output flange arrives in 2 weeks.

you guys are crazy with your GTR setups

SIMPLE solution

S13/14/15/y33/y32/gtst/r32/r33/

all the diffs are interchangable

you might not have mounts for the attessa shit, but you can make them

I have an s13, with WGNC34 rear cover, s14 solid diff mounts, and Nismo 2 way

swap the input shaft for the driveshaft from teh C34 to the s13 diff, bolt that ish up

throw some greddy or veruspeed gear oil in there and your good to go guys.

just make sure you get the output shafts wit hhte same number of bolts (6 i think?)

you guys are crazy with your GTR setups

SIMPLE solution

S13/14/15/y33/y32/gtst/r32/r33/

all the diffs are interchangable

Yup, I know. I work for a Nissan dismantler :)

you might not have mounts for the attessa shit, but you can make them

I have an s13, with WGNC34 rear cover, s14 solid diff mounts, and Nismo 2 way

swap the input shaft for the driveshaft from teh C34 to the s13 diff, bolt that ish up

throw some greddy or veruspeed gear oil in there and your good to go guys.

just make sure you get the output shafts wit hhte same number of bolts (6 i think?)

Yeah but in the end it seemed crazy for me to buy another diff (I'd already bought 2 others) when I had 80% of a GTR diff already. The flange only cost me $300 & now it bolts straight in and includes the mount for the ATTESSA pump. The axles were easy (don't believe what people tell you) and I get to have a mechanical LSD as opposed to Viscous

Yup, I know. I work for a Nissan dismantler :)

Yeah but in the end it seemed crazy for me to buy another diff (I'd already bought 2 others) when I had 80% of a GTR diff already. The flange only cost me $300 & now it bolts straight in and includes the mount for the ATTESSA pump. The axles were easy (don't believe what people tell you) and I get to have a mechanical LSD as opposed to Viscous

So what is the final parts needed?

Diff?

Output shafts?

LH and RH axles?

Anything else?

So what is the final parts needed?

Diff?

Output shafts?

LH and RH axles?

Anything else?

For me personally? CV grease & LSD oil. Otherwise I'm not quite sure I understand the question Darrin...............

EDIT : Sorry, I just read further up the thread. I'm fitting it all on Saturday so provided I don't run into anymore issues I'll post the full diff swap with pics on Sunday

Edited by tRUkbOY

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
    • You can probably scrub the rust with a toothbrush or something. After you get the rust off flush well with water to neutralize and you will probably want to also use a fuel tank sealer to keep it from rusting again.
    • The sodium citrate solution is designed to buffer the citric acid to keep it from attacking metal quite so much, the guy that came up with that recipe did a ton of testing on how much metal loss occurs over time and it's nothing crazy unless you forget about it for months:   
    • Ohhh I see lol To be honest the main reason why I wanted to start modding is because of a business trip to Japan and Indonesia. I saw many cool and modded cars all throughout in these countries, especially Japan. I myself am of Chinese+Japanese nationality and when living in china (never lived in Japan js my dad side lol) I remember staring at these cars pass by with their loud tacky exhausts and insane wide body kits. And when I went back to Japan, I got even more invested even asking people about their cars and why they modded. Most gave similar answers to what you said but funny enough one guy just said that he saw the need for speed movie being filmed once in Tokyo I think near Shibuya Crossing and got inspired to tune and mod. After that I just started to fantasize on owning a car like that. Also tbh I prefer the R32 over the R34 it's just the R34 is more iconic lol (also apparently better aftermarket support than the R32) and my only goal really is just to make the car mine and make it fun to drive. As much as I love my Cayenne it's pretty bland to drive. Sure the interior is nice and pretty, gives you attention yada yada but I've wanted to experience what it is like to have a car that is truly yours. I suppose thats the goal so far. Haha if you find where I'm from, then sure. Ill help you out on your next "financial decision"
×
×
  • Create New...