Jump to content
SAU Community

Recommended Posts

the alloy bushes jammed in the rear cradle like this serve the same purpose as the Noltec sub frame bushes.

Yes the end result is the same and NVH is very much the same anyway.

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

all

staying on tie rod topic lol

im in 3 minds

JJR

Tein

Kazama

i wanna know which ones would last a while and be best to use.

looks like JJR arent too bad, but would they last ?

hhmmm

also they look pretty dodgy lol

rocket and VPW keep the full range of replacement rose joints, i have a set of JJR ones in cats car but with QA1 ends as the originals lasted about 2 event's before gettng sloppy. I ran ikeya formula rod ends on my 180 with no dramas for 3 years....

A mate in QLD recently snapped his stock tie rods and then after "upgrading" also snapped his JJR tie rod in his drift A31. Not the best quality by the looks of it, currently replacing them with tein tie rod kit that includes tie rods/tie rod ends and spacers for more lock. rrp $359 through www.isc-performance.com.

Ryan

Any photos of the failures? I am amazed he snapped the std ones! Bend maybe, but snap? The material grade they use normally means they are very ductile....this is assuming he didnt right off the entire side of the car...in which case not the fault of the std ones :)

Ive got kts ends on ikeya rods at the moment

daily driving havent noticed any wearing yet but they havent been on long

might end up getting the ones dave has as I think they would probably pass regency down here

whats the point of you fitting them ?

you getting bump steer

or you just need new ends

if you want to do the rears do it properly and swap in a s13 non hicas rear craddle less hassle in the long run

its what Ive done

Edited by 1400r

I already have a diff in my rear with some bushes etc etc, so owes me too much money to swap to an S13 cradle. If anything i will go GTR that way i get all the alloy goodness, bigger shafts etc and then just get new shocks (again ;))

Yeh, i needed new ones so if im going ot be spending hundreds on Nissan OE, may as well spend a little less and get something that may end up better.

Im going to pull out my rears and make up some of my own :(

  • 1 year later...

There is also these ones http://www.tuneagent.com.au/public/merchan...Item.aspx?id=22, they also fit the R34's.

Australian mob plus they come with a 1 year warranty. Look to be of pretty good quality, and for the price you cant go wrong.

Just orderd some myself, so gonna see how they go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...