Jump to content
SAU Community

Recommended Posts

a 1993 R32 GTST 179000 on the dial Suspension was installed at 170000, engine was installed a 171000 as was the clutch, and the turbo has covered less than 2000 km

R33 RB25DET

20 thou oversize forged pistons

forged h beam rods

reconditioned (new springs valves ect) and lightly ported head

N1 oil and water pumps

ACL race bearings

Cometic metal head gasket

ARP head studs and rod bolts

R33 Gearbox

R33 Differential

Garrett GT3076R Turbo

Tomei Poncams

600cc injectors

Z32AFM

HKS Hyper 3.5" exhaust with custom front pipe

Splitfire Coil Packs

OSgiken TS2BD twin plate clutch rebuilt by NPC

C’s Short Shifter

GFB Stealth FX Blow off valve

Bosch 700hp rated fuel pump

Apexi Pod Filter

Apexi PowerFC

Greddy Profec B spec 2 Boost controller

Custom FMIC

Custom intake piping

Oil cooler and filter relocation kit

Suspension and Braking

HKS Hypermax 2 coil over suspension

Front and rear strut bars

B pillar Brace

After market sway bars

JIC adjustable castor rods

JIC adjustable upper arms

Whiteline Pineapples

R33 GTR Brembos with DBA 5000 rotors

Front: 17 X 8 wheels with 235/40 semislicks

Rear: 17 X 9 wheels with 255/40 semislicks

Exterior and interior

Full respray- Custom Blue

Genuine GTR Bonnet and Grill, Front bar, and rear spoiler

GTST Type M side skirts

GTST Type M rear pods

Genuine R32 GTR Front and Rear seats

Genuine R32 GTR Door trims

Genuine R32 GTR Headlights

Nismo Gearknob

Audio

DVD player with 4 inch screen

6.5" Jensons in the back and JL 6" Splits @ the front

Last tune was a very safe 260rwkw it was making 300rwkw previously but it was not safe, a safe 300rwkw is only a thicker head gasket away! At 260rwkw this thing still really hauls and handles beautifly too as it has that little bit of extra attention paid to the suspension

I am asking 24,000 neg. this price is mostly designed to ward off dreamers and tyre kickers, if you are interested we will talk! I have included a picture of the car with 18inch starcorp impuls, if the buyer perfers these wheels could go on the car instead as I still have them at home.

PM me to discuss the car. Hope to hear from you soon!

Andy

OFFERS AROUND 20K WILL GET YOU THIS CAR TODAY!!

post-21318-1193703070_thumb.jpg

post-21318-1193703223_thumb.jpg

post-21318-1193703242_thumb.jpg

post-21318-1193703254_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/191365-1993-r32-gtst-with-rb25/
Share on other sites

Thanks for the kind comments guys! It will be sad to see her go after all the blood sweat and tears but after the best part of 2 years i am ready for a change!

my kind of no bullshit car!

ive never seen it... shooooooooooow me.

you could but it and see it all the time :ninja: ha ha I will even give you a special members price :)

someone buy this car.....this is an awesomely kept and run car has everything you need and nothing to put in except fuel...

I have been in this car and its a wet dream on wheels.

  • 1 month later...


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...