Jump to content
SAU Community

Recommended Posts

for $5k more you can have my 34... ;)

As for writeoffs, a friend purchased a WRX from a caryard, later he found out it was an economic wrieoff in NSW, they fixed it, shipped it over here and rego'd it...... It can happen, not sure on the legal grounds.

How many test pilots and time wasters did you have ?

Im about to hang the next 1 :)

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

The sad truth is that most of us are driving japanese write offs. (economical)

The cost of repairs there is prohibitive and most are repaired in australia . Plus , correct me if im wrong , aftrer a car hits 5years old , it needs an inspection every year , plus if its crashed (even slightly) its deemed unregistable.

As far as the quote of 200rwks , I would ask for a recent dyno print out.

Good luck in the car purchase though and remember to trust your gut.

cheers for that info. i havent heard of anything regarding the 5yr rule. my all of my cars bar my current have been older than 5yrs. i know there is something in te eastern states with roadworthy checks being done. on that topic, what tings fitted to the car are defectable. i think its the bov, exhaust db level and hopefully thats it. are front mounts legal? and 18" wheels.

The car MUST be street legal for the caryard to sell it (dosen't mean it is) .

Rims can be 1 " bigger than stock I think so unless its a GTR , no they are illegal (correct me if im wrong)

Plumb back blow off valves are'nt illegal (depending on the copper looking under the hood)

One place for you to lookout for though is the shock strut towers under the bonnet , Look to see if the welds are identicle on both sides.

i found out from the dealer that the car is from strathalbyn. i was told the guys name but i wont post it on a forum. if anyone was the owner of a maroon r33 gts-t that has the mods mentioned above and maybe more, or knows of it, it'd be cool to have some feedback on it. all the previous ideas have been helpful too guys. also had a aftermarket heavy duty clutch.

dude just get it checked out mate the person who owned probly aint on here and no-one can give u a straight answer coz have not seen the car inperson ask the car yard guy can u take it to your mechanic for full engine check etc dnt be bitten mate just my 2 bobs gl with it mate. :ninja:

Sounds like it might be redgtst's car - I think he was from out that way.

It wouldnt be, see the replies below:

Does it have a 400R front and GTR rear wing? If so, be wary!! Redgtst crashed his 33 a few months back and it was an economical write off. May be repaired, so have it inspected whatever you do. if they refuse to allow an inspection, DONT BUY IT!
If an insurance company declare it a write off (economical or otherwise) it can not be registered again in Australia.(the costs make it prohibitive with engineering inspections etc for regency - and it MUST have a FULL regency inspection)

I found this out when I was looking at buying back my car after front end damage. (I would be able to fix it but never register it again) My only alternative was to take it to another repairer who was able to fit some "Reconditioned" parts rather than new from Nissan parts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...