Jump to content
SAU Community

Recommended Posts

Saw Rhino (Dave) this morning on south pine or old northern road this moring (I get the 2 mixed up), I also parked near a purple R34 in the kings carpark at Milton, Nice kit dude.

thanx...which one were you in?? didnt see any skylines....

Was just walking out of the fish'n'chip shop on the corner of gympie road and robinson road... Didn't think you would have seen me, my 34 was parked behind the bushes.

Spotted * white R33 with Big tommy Kiara sticker down side, kit and five spoke white rims looks nice parked at a residence.

Spotted * Black R33 S2 gtst BP woodridge, kingston/logan road. yesterday, nice ride... no gday.. nothing.

Spot me! :D

Spotted a real nice orange R33 when it pulled up along side me going past browns plains plaza this afternoon.... :D

if your from here mate"nice motor" :D

yep i seen this car few weeks ago. and browns plains, very nice orange R33 sounds sweet. 1 headlight not working.

Spotted* gunmetal grey R32 GTR, logan road. 12:10 pm today.

Edited by silverbulletR33

"Saw a sweet lookin R32 Silver Sedan near coopers plains/sunnybank border (forgot road name) and a black R33 Sedan that's always parked cross from McDonalds Sunnybank. Nice body kit too.

Go the sedans "

oooo that could of been me!! i was driving to willobank for that 7/11 thingo. Did it have a cooler on the front? :sick:

Edited by gtrchick

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...