Jump to content
SAU Community

Recommended Posts

spotted JDM34 today on lytton rd at the traffic lights at the end of creek road....i was going to wave, but i was driving the hilux so you prob would have been like..."He's gay!!" so i didnt.

noice car!

Is that your new car??

if it is...

Awesome looking beast, mags suit it really well...and the colour...mmm....can i rub it?

OH and spotted a red r33 on creek road yesterday arvo about 5:30ish.

nice red and black mags.

Spotted a blue 32 that looked very much like Bunta's car in a very very rural setting last night. Some hot looking chic driving it with what looked like bunta in the passenger seat. Whats up with that!!!!!

Spotted AFRO8 Bayside Blue 34 this morning on ippy motorway around 8.30am. I was in my shitbox daily driver, the mighty rolla :closedeyes:

And i think i'm in love with Choyda's new ride (in his sig)... That looks hot mate!!!!

spotted JDM34 today on lytton rd at the traffic lights at the end of creek road....i was going to wave, but i was driving the hilux so you prob would have been like..."He's gay!!" so i didnt.

noice car!

I saw you in the lux the other day, and you didnt bloody wave. I DID! So I looked like a fool.

Spotted a blue 32 that looked very much like Bunta's car in a very very rural setting last night. Some hot looking chic driving it with what looked like bunta in the passenger seat. Whats up with that!!!!!

how else am I going to tune it in 4th gear?

Spotted AFRO8 Bayside Blue 34 this morning on ippy motorway around 8.30am. I was in my shitbox daily driver, the mighty rolla :w00t:

And i think i'm in love with Choyda's new ride (in his sig)... That looks hot mate!!!!

should have waved!! :domokun:

oh well , next time, :w00t:

Spotted Tiffany (51PRY) on Logan Rd on Tuesday night u-turning on Logan Road. Drove side by side with a de-badged grey 32GTR through the city last night too.

Hey Damo! I saw you pass me too! :domokun:

......it looks & sounds sex!

I saw you in the lux the other day, and you didnt bloody wave. I DID! So I looked like a fool.

bahahah....yeah prob was tryin to kept it on the road...its real hard to keep straight, or maybe thats just me....where was i??

spotted a black r32 on ipswitch rd heading south at about 6:50 tonight....was to far back to see plates etc.

sounds hot though.

Spotted a very cute boy washing his silver Stagea at the car wash on Beaudesert Road in Acacia ridge. I didn't wave because I stalled and was cranky. Then embarrassed. Then Shy. But hello anyway!1

Spotted a very cute boy washing his silver Stagea at the car wash on Beaudesert Road in Acacia ridge. I didn't wave because I stalled and was cranky. Then embarrassed. Then Shy. But hello anyway!1

lmao...Anna shy?? couldnt be..

Spotted white r33 on creek road about 12:00 today...i was in red rooter....nice BOV sound :unsure:

Spotted dark/black R34 GTR with plates: 'CHOY' - (I'd assume it's CHOYDA's)....in the Valley last night around 6pm

One nice looking car.....

Edited by tim_wagamama

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...