Jump to content
SAU Community

Recommended Posts

I have read heaps of threads about rough idle, stalling etc etc and it seems to come up very often that intake leaks are the source of the problems.

Its pretty hard to find a small leak when the car is running by listening for it, especially with the noisy engine fan, and it can get messy with a can of wd40 or something similar being sprayed on every seal and clamp.

So I have been thinking about another way of checking for leaks.

Has anyone considered making a blank that fits inside the rubber hose on the intake pipe where it bolts onto the throttle body, and another blank that fits over the air flow meter where the fliter attaches. Then fit a rubber tyre valve stem into one of them and pressurizing the intake system to say 20 psi.

It would be a lot easier to listen for leaks this way when the engine is off. Also I was thinking you could not have a blank on the throttle body pipe, but instead put one on the dump pipe/exhaust tip and pressurize the whole intake/exhaust.

Can anyone see a problem with this? Im thinking of making some blanks up to check my engine but dont want to damage anything in doing so.

No problem, in fact i have seen kits for sale on the internet for this very purpose. I think it would work well.

I wouldnt go where the air flow meters are, i would go just after the turbos. Turbos them selves wouldn't be 100% sealed around the shaft.

Edited by GTR1993

Already been done before. Here's the general instructions.

You can do a leak test.

What you'll have to do is,

1. take your pod and AFM off.

2. use a baked bean can (full) and put it into your rubber intake pipe (assuming its still the stock one).

3. tighten up the hose clamp onto the tin creating a seal.

4. Open the throttle body with a brick on the accelerator pedal, so you can read pressure on the boost gauge.

5. take a hose that is plumbed into your intake between the turbo and the plenum or off the plenum itself.

6. Get an air compressor and pressurize the system through the hose and get someone to read the psi on the boost gauge. you only need about 5psi. you can use the compressors at the servos.

7. Listen for a leak. And use the soapy water in the spray bottle to find exactly where it is if need be.

It is easier to find a boost or pressure leak using this method because the car is not running and is easier to hear and locate.

Thanks for the feedback guys, it certainly seems a better way than trying to listen for a leak when the engine is running. Not surprised its been done before tho.

Funny to hear the different ways people use to plug the intake up. Maybe jam a spud in there, it works well up the exhaust :huh:

4. Open the throttle body with a brick on the accelerator pedal, so you can read pressure on the boost gauge.

I forgot to add, this is if you've got a mechanical boost gauge installed. But it will pressurize your plenum to check for leaks on it also.

Interesting you say this about pressurizing the plenum. This must mean that rb cams have 0 overlap. ie only intake or exhaust open at any time? Therefore pressurizing cylinders without losing pressure through exhaust ports is possible?

I did it on mine. My boost gauge is taking its signal from the plenum so I can only conclude its pressurizing it.

But i have heard of pressure being lost out of the exhaust which means they will have overlap.....I think.....enlighten me.

The rb25 plenum can be pressurized without the air leaking through the exhaust valves. I just tried it and the first time there was a leak, but i cranked it over a little bit and it sealed up. Removed afm, blocked the intake pipe, and pumped it up to 5psi through the fuel pressure reg hose that goes onto the manifold. :P

Did mine after some recent tuning issues and found a few small leaks. Got a piece of pipe and welded a hat onto it in to whichwe welded an air hose fitting and clamped it on behind the afm. Worked a treat and helped us solve a couple of niggle issues that has plagued us for a while.

I wouldnt do another build without doing this before it went to the dyno. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
    • That's my life. Past-Duncan has a lot to answer for
×
×
  • Create New...