Jump to content
SAU Community

Recommended Posts

I have read heaps of threads about rough idle, stalling etc etc and it seems to come up very often that intake leaks are the source of the problems.

Its pretty hard to find a small leak when the car is running by listening for it, especially with the noisy engine fan, and it can get messy with a can of wd40 or something similar being sprayed on every seal and clamp.

So I have been thinking about another way of checking for leaks.

Has anyone considered making a blank that fits inside the rubber hose on the intake pipe where it bolts onto the throttle body, and another blank that fits over the air flow meter where the fliter attaches. Then fit a rubber tyre valve stem into one of them and pressurizing the intake system to say 20 psi.

It would be a lot easier to listen for leaks this way when the engine is off. Also I was thinking you could not have a blank on the throttle body pipe, but instead put one on the dump pipe/exhaust tip and pressurize the whole intake/exhaust.

Can anyone see a problem with this? Im thinking of making some blanks up to check my engine but dont want to damage anything in doing so.

No problem, in fact i have seen kits for sale on the internet for this very purpose. I think it would work well.

I wouldnt go where the air flow meters are, i would go just after the turbos. Turbos them selves wouldn't be 100% sealed around the shaft.

Edited by GTR1993

Already been done before. Here's the general instructions.

You can do a leak test.

What you'll have to do is,

1. take your pod and AFM off.

2. use a baked bean can (full) and put it into your rubber intake pipe (assuming its still the stock one).

3. tighten up the hose clamp onto the tin creating a seal.

4. Open the throttle body with a brick on the accelerator pedal, so you can read pressure on the boost gauge.

5. take a hose that is plumbed into your intake between the turbo and the plenum or off the plenum itself.

6. Get an air compressor and pressurize the system through the hose and get someone to read the psi on the boost gauge. you only need about 5psi. you can use the compressors at the servos.

7. Listen for a leak. And use the soapy water in the spray bottle to find exactly where it is if need be.

It is easier to find a boost or pressure leak using this method because the car is not running and is easier to hear and locate.

Thanks for the feedback guys, it certainly seems a better way than trying to listen for a leak when the engine is running. Not surprised its been done before tho.

Funny to hear the different ways people use to plug the intake up. Maybe jam a spud in there, it works well up the exhaust :huh:

4. Open the throttle body with a brick on the accelerator pedal, so you can read pressure on the boost gauge.

I forgot to add, this is if you've got a mechanical boost gauge installed. But it will pressurize your plenum to check for leaks on it also.

Interesting you say this about pressurizing the plenum. This must mean that rb cams have 0 overlap. ie only intake or exhaust open at any time? Therefore pressurizing cylinders without losing pressure through exhaust ports is possible?

I did it on mine. My boost gauge is taking its signal from the plenum so I can only conclude its pressurizing it.

But i have heard of pressure being lost out of the exhaust which means they will have overlap.....I think.....enlighten me.

The rb25 plenum can be pressurized without the air leaking through the exhaust valves. I just tried it and the first time there was a leak, but i cranked it over a little bit and it sealed up. Removed afm, blocked the intake pipe, and pumped it up to 5psi through the fuel pressure reg hose that goes onto the manifold. :P

Did mine after some recent tuning issues and found a few small leaks. Got a piece of pipe and welded a hat onto it in to whichwe welded an air hose fitting and clamped it on behind the afm. Worked a treat and helped us solve a couple of niggle issues that has plagued us for a while.

I wouldnt do another build without doing this before it went to the dyno. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...