Jump to content
SAU Community

Recommended Posts

  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Some interesting points from Bill Tuckey.

Try read it with an open mind and some patience as it is long, but this is the message that needs to get out to convince people that staying under the speed and .05 limit will not guarantee your safety on the roads.

It's time the government stopped making revenue from speed.

http://www.theaustralian.news.com.au/story...5010800,00.html

Emphasis in all Australian states has shifted from surveillance and visual deterrence to speed measurement, as if this is the main crash factor apart from alcohol.

The overemphasis on speed as a factor justifies government investment in ever more sophisticated technology to trap more vehicle users; in fact, government polling shows this gives voters a nice warm feeling because the authorities are seen to be doing something. Thus, as mobile road patrols vanish, we are losing the ability to check on the use of phones, suspended licences, outstanding warrants, underage drivers, the wearing of seat restraints, lane discipline, tailgating, unroadworthy vehicles and the rest.

No longer do police sit and watch for those rolling through stop signs, as they did in the 1970s, nor can they lurk at railway level crossings to stop the growing incidence of vehicle-train crashes. They can't. They simply don't have the manpower, or are diverted to more revenue-worthy pursuits.

Thanks for that Geoff.

and pulling all the bombs off the road...

Went past a 40/45 series land cruiser this morning on the way to the shops to get milk and it was so full of rust if he had hit a pole it would fall apart...

I could see the pedals/feet through a rust hole in the door at the lights...

Man i agree with that Australian article, it's all about public perception to what causes fatal crashes and not actual facts. Same as the whole every import driver is a hoon perception and that hoon's cause fatal crashes....

  • 3 weeks later...
Tarragindi off-ramp (M1) on Brisbane's Southside

wow, they're going to get a shitload of tickets out of this one

Saw the camera busy flashing yesterday (targeting car towards city).. i guess not many people realize there was a camera installed in between highway.

Also spotted some lines on Kingsford smith drive somewhere near Harvey st (Eagle Farm) ..? can't see the nice little box tho.. :D:D Anyone seen this ?

  • 3 weeks later...
As far as I can tell it is about where the red circle is in the map, on the Hwy there is a gap where the popo used to sit with their radar trap.

That's the one that i saw few weeks ago busy flashing.. so i guess it just started to operate now.. :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
    • They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
×
×
  • Create New...