Jump to content
SAU Community

Recommended Posts

Hi all

I have a R34 GTT with the following suspension mods:

- tein super streets

- whiteline front (24mm) and rear sway (20mm) bar both on soft

- front and rear camber kits

- front castor kit

- aligned to SKs settings, pretty much everything is SK spec except coilovers and slightly smaller rear bar

Problem I am having is that when I take say a hard left corner, the rear seems to hop hop hop as if the rear passenger wheel is coming up and off and onto the road again. Its either that or the tyres are rolling on the side so much that Im getting that feeling. it is hard to explain but its like the rear of the car is hopping along to follow the cornering line.

The front seems fine to me and is well planted.

Any ideas what it could be? or what I should try to get rid of it? is it too much body roll?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/193750-rear-seems-to-hop-on-hard-cornering/
Share on other sites

does the car actually kind of buck? called pig rooting? happens in slower, tighter corners. and it happens when you are getting on the power just before the apex?

does the car actually kind of buck? called pig rooting? happens in slower, tighter corners. and it happens when you are getting on the power just before the apex?

Dont quite get what you mean by bucking BB? But im def. not getting on the power early

like as in the car is behaving as though it was a mechanical bull. ie jerking up and down as you are cornering?

I get that, but only on the street. I know my rear springs are too hard, but is there another reason it happens?

I seemed to have that problem at one stage :) my cars left hand rear shock had gone simple bounce test later and a replacement found and its been all good so far

it bounced around on tight corners but also on long sweeping corners at speed :) however it may have no relevance as i have a 33 but still thats my 2 cents hope it helps :)

Edited by SeanO
Were the Teins new?

You keep having weird problems with this car eh.

Are you slowing or accelerating through 80km/h during this corner?

Have you got a new bike yet?

Hahaha i dont really have any problems at all, i always think i do but its always fine in the end, i think its just my fussy self hahah

i think ive been pretty lucky to have everything go well with the car so far (knocks on wood)

teins are new, 1 year old, only done maybe 10 thousand km on them

its like a tight bend, im only doing maybe 50km/hr, maybe its just the nature of the bend, its one of those ones that get tighter as you get into it

naah still trying to sell the white cibby first, then onto a 600cc hopefully

i have exactly the same problem too. Theres a nasty winding road when i got to Bendigo its like a U turn on the middle of the hill and each time i turn it seems the tyres are slipping at the rears. Sort of felt like going into a dip and the car bounce back. I installed the tein read my signiture for specs.

Sounds like, insufficient rebound damping in the shocks to control the spring wind up caused by the rear squat on acceleration. Typical of a poorly matched spring rate and shock valving.

If you have adjustable shocks, try winding them up towards full stiffness. It sometimes helps.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
    • Got you mate. Check your email!
    • I see you've never had to push start your own car... You could save some weight right now...
    • Sounds good.  I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear?  If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific.  Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time. It will stick to the clear coat provided it has been appropriately scuffed/prepped first.  When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean?  So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time.  The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint.  So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear?  Life seems so much simpler if you prep, fill, primer, colour then clear.  There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal.  A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 
×
×
  • Create New...