Jump to content
SAU Community

18s Scraping On An R32

julion
 Share

Recommended Posts

julion Community Regular

julion

Posted
Posted

I just got some 18s with 245/40/R18 tyres

the inside of the front tyres scrape on a metal piece (looks like part of the suspension)

It only really does it on hard conering, but is very off putting and Ive put my stockies back on the front.

Spacers kind of worked, but i was thinking about getting some smaller tyres?

is there any easy way to remedy this situation?

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/194083-18s-scraping-on-an-r32/
Share on other sites
BHDave Grand Master

BHDave

Posted
Posted
hitting stuff with a hammer sounds like a good plan to me :ermm:

does anybody know the bit the wheels are scraping on im talking about?

will it matter if i tap this with a hammer?

no, it's a f**king stupid idea.

I'm guessing it's the upright that attaches to the top of the hub and the upper control arm and the tyre is flexing on hard cornering. Which means your wheels must have a shocking offset in order to 1) fit 245's without scrubbing on the guard and 2) sit the tyre in close enough to the upright to give problems on turning.

If it's the bit i'm thinking of then i don't recommend it. Though to be honest i dont think you could do more than dent it as it's a pretty beefy unit.

roll guards, flatten seams, remove inner guards, go for it. don't go anywhere near the arms, hub or uprights with a hammer

adam-__- Grand Master

adam-__-

Posted
Posted

No way would I recommend knocking the hubs, swaybars or anything like that either, I was only talking about the guards.

I don't see how a wheel would rub against the hubs or uprights though. Only thing I would see it rubbing is the coilovers or brake calipers.

Taleb Tyres Proficient

Taleb Tyres

Posted
Posted
no, it's a f**king stupid idea.

Haha hey buddy i agree with you there, i dont mean going kamikaze with a hammer on the inside of the wheel area hoping for the best, Ive heard and dealt with enough of these problems to know that most of these issues are small easy fixes, most.

Depends where your problem spot is, get a pic if you can mate we can help you out more.

If your not sure where it is get a crayon or something similar and go over the inside edge of the tyre, or wherever you suspect its rubbing, drive around the block, have a look and see where its hitting..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Just_a_datsun
      RB26 block, rb26 head

      By Just_a_datsun · Posted

      Block bump. $400. As above cyl 6 needs bore or sleeve.
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I would think making the argument that the travel is limited by a spring flexing against a spring perch as "the same method". Later on in the document they do state that the spring can't bind on full bump travel and cannot come loose in full rebound travel as well. (which is all very sensible). The laws are actually pretty sensible and reasonable. It's just that the people who enforce and check them don't actually read them or know them accurately. "Oh, coilovers? Instant fail mate. Don't even need to look at it." - Guy who will be instantly reported by me. There is probably merit to people who do get defected for height also get defected for the suspension in that state that allows it. I did never consider the people who are complaining about coilovers being picked on are also running around at 50mm off the floor.
    • Kinkstaah
      Ethanol Content Sensor - Always at 11%?

      By Kinkstaah · Posted

      I think given SAU's knowledge of E85 we can strongly conclude that 10% ethanol in almost any situation is entirely fine. Almost all of the myths against E85 were overblown, let alone E10.
    • The Bogan
      Blue slip

      By The Bogan · Posted

      From your link See bold text, is this referring to damper settings, if so that may a issue for "some" inspectors, I cannot see aftermarket coilovers having the evidence that "must be available that its functional performance is equivalent to the original" Maybe just remove the adjustment knows and hope for the best???? Meh 5.2 Suspension travel In all instances, modifications to a vehicle’s suspension must ensure the integrity of the system and not compromise the ride quality. At least two thirds of the original suspension travel should be maintained in both directions (rebound (i.e. extension) and bump (i.e. compression)), and rebound must be limited by the same method used by the vehicle manufacturer or if this is not practicable due to the nature of the modification, an equivalent method. If an alternative method is used, evidence must be available that its functional performance is equivalent to the original.
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      They actually don't - They adhere to VSB14 rules just like Victoria. The rules are against CABIN adjustable height, and it quite clearly states that the height has to be within parameters. I asked the VASS engineer to confirm this when I got my car engineered and they refused to engineer the coilovers because they didn't meet the requirements for requiring engineering. (mine are height adjustable.) People "Not wanting to bother" with "Actually reading/knowing/adhering to the rules" should result in fines and immediately losing the ability to issue blue slips and/or RWC's in Vic.
×
×
  • Create New...