Jump to content
SAU Community

Recommended Posts

The RX7 is a serious proposition.

It can challenge the R33 GTR on both strip and track. The two cars have very different driving characteristics and styles.

For very little the RX7 is put into low 12's on the 1/4 and factory stock is superior to the GTR as a track car with reasonable endurance. In the first bathurst production series (93/94?) the RX7 raced the R32 GTR I believe and the 'others' and beat them. It went on to dominate for the next few years in that particular area.

Link to comment
https://www.sau.com.au/forums/topic/19541-rx7-vs-skyline/#findComment-410797
Share on other sites

Both cars is a cult in their own right. Really depend on you want to set up the car for i reckon. I have seen mad RX7s drifting like no tomorrow and mad GTRs runing like crazy down the drag strip. But than again RX7 are great for the drags as well. GTR have the advantage of the Attessa and probaly have more grip but other than that both cars are SICK. I think the RX7 are sexier and the GTR are more meaner ;)

Link to comment
https://www.sau.com.au/forums/topic/19541-rx7-vs-skyline/#findComment-411236
Share on other sites

Originally posted by Nismodified

i think in the right hands the RX7 is a faster car.

That is debateable, but whatever the case, the Supras, NSXs, and GTRs tend to dominate the JGTC in Japan. Looking at the results of rounds 1-3 it's GTRs, NSXs, or Supras in the top 5, with the best RX7 result being 18th in round 3.

Link to comment
https://www.sau.com.au/forums/topic/19541-rx7-vs-skyline/#findComment-411342
Share on other sites

JimX,

JGTC, does not provide a real insight into the 'true' car. I mean none of those things are even remotely like the road going versions.

Talking as you drive on the Australian road, the RX7 is more than a match.

18th isn't a bad result for the 1.3 litre chooker.

Link to comment
https://www.sau.com.au/forums/topic/19541-rx7-vs-skyline/#findComment-412081
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...