Jump to content
SAU Community

Recommended Posts

Got my 120 degree intake made up yesterday, fitted it today, seems a hell of a lot more responsive (had to be careful, pissing down out here). Need to get my BOV adjusted properly yet, every now and then when pulling up it stalls, and yes its a plumb back. What is the best way to adjust it?

1st pick shows with original.

post-536-1196664316_thumb.jpg

2nd pick shows both side by side, alot of piping taken out.

post-536-1196664389_thumb.jpg

3rd pick shows new pipe fitted up. Even looks alot better.

post-536-1196664438_thumb.jpg

Photos were taken with my phone, i left my camera at home, did the job at work.

Link to comment
https://www.sau.com.au/forums/topic/196148-120-degree-intake-pipe/
Share on other sites

i think it would make a difference. he's eliminated 2 sharp-ish bends which will cause a bit of turbulance and restriction. the last bend is open in terms of the angle.

i like the design. to get to your last 3 plugs you need to take the crossover pipe off anyway. at least now its only a matter of 2 clamps and you can swing it around. the oil filler cap will be a bit of a problem though.

I'll be going for exactly this kind of setup in about a months time. SydneyKid and a few others recommend it. RE in the way of the sparkplugs/coils - the only piping I've seen that isn't is a forward facing plenum, any other aftermarket IC piping is also in the way and has to be taken off for work. I'll be trying Hypertune's kit, apparently it's 5 piece.

Oil filler cap isn't that big of a problem

I have a pipe much similar to that

When I'm doing oil, I'm doing plugs at the same time, so that pipe is off!

If I needed to "top up" you can still get the cap off easily enough.

Bonnet isnt as problem and i can live with the oil filler cap, 2 clamps and its off. I think it even looks better. Intake temps have dropped a little as well, i monitor those with one of those jaycar temp probes.

Also, Wolverine: That's the exact same one I run. I don't find hose clamps are needed to be loosened at all.

they might have modified the kit slightly, i got mine a while ago. mine fowls slightly so loosening the clamps is enough to unscrew the cap.

or possibly the location of the cooler is different on yours which lifts it up the few mm's to clear the cap?

Edited by wolverine

just throwing it out there.

wouldnt it be more beneficial to get a forward facing intake plenum.

im installing one atm and it gets rid of almost 2m of piping and looks clean.

nice and clean. u can access the engine block without all the piping in the way

Edited by r33cruiser

plenum=200-400 ebay

bolts, nipples etc=20

xf TB= 50 ebay

270-470. and is a long term fix with greater benefits.

labour costs=NO

=diy

http://www.skylinesaustralia.com/forums/to...um-t181826.html

Edited by r33cruiser
Another negative comment, didnt get any last night ay?

:)

Don't get me wrong.

It's the design I would do from the start if I was doing a fmic.

Gibson motorsport used this on the race R31's..

I just wouldn't have bothered if it already had the U shape across the motor like he already had.

each to their own.

had to do this too, as my turbo was in the way of the stupidly wide arc made by the original piping. i dont think i want it close to the exhaust anyway

i dont like the look of it tho, so will go some sort of front facing plenum eventually

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
×
×
  • Create New...